Dodge 2008 Avenger Owner'S Manual Download Page 17 | Manualshive

Page: 17 / 467

background image

the vehicle. The system will shut the engine off in two
seconds if someone uses an invalid key to try to start the
engine.

NOTE:

A key that has not been programmed is also

considered an invalid key, even if it is cut to fit the
ignition switch lock cylinder for that vehicle.

During normal operation, after turning on the ignition
switch, the Vehicle Security Light will turn on for three
seconds for a bulb check. If the light remains on after the
bulb check, it indicates that there is a problem with the
electronics. In addition, if the light begins to flash after
the bulb check, it indicates that someone used an invalid
key to try to start the engine. Either of these conditions
will result in the engine being shut off after two seconds.

If the Vehicle Security Light turns on during normal
vehicle operation (vehicle running for longer than 10

seconds), it indicates that there is a fault in the electron-
ics. Should this occur, have the vehicle serviced as soon
as possible.

NOTE:

•

The Sentry Key

t

Immobilizer System is not compat-

ible with some aftermarket remote starting systems.
Use of these systems may result in vehicle starting
problems and loss of security protection.

•

Exxon/Mobil Speedpass™, additional Sentry Keys

t

,

or any other transponder-equipped components on
the same key chain will not cause a key-related
(transponder) fault unless the additional part is physi-
cally held against the ignition key

being used when

starting the vehicle. Cell phones, pagers, or other RF
electronics will not cause interference with this system.

All of the keys provided with your new vehicle have
been programmed to the vehicle electronics.

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

15

2

«
...
15
16
17
18
19
...
»

Summary of Contents for 2008 Avenger




















































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2008 Avenger

Brand: Metra Electronics Pages: 2

Brand: Actia Pages: 37

Quattroporte Automatic

Brand: Maserati Pages: 272

Brand: Draw tite Pages: 4

Brand: Mercedes-Benz Pages: 329

Brand: Black Horse Off Road Pages: 7

2003 Silhouette

Brand: Oldsmobile Pages: 466

Brand: Thule Pages: 8

Brand: SAFARI Pages: 5

Brand: Pet Gear Pages: 4

IGNIS 2022 Series

Brand: Suzuki Pages: 570

Brand: Volvo Pages: 7

Brand: Speedtech Pages: 12

QuadraTop Adventure Top S

Brand: Quadratec Pages: 13

Brand: ULTIMATE SPEED Pages: 18

Brand: DV8 Pages: 4

Brand: DV8 Pages: 6

Brand: Autostart Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands