Dodge 2008 Avenger Owner'S Manual Download Page 18 | Manualshive

Page: 18 / 467

background image

Replacement Keys

NOTE:

Only keys that are programmed to the vehicle

electronics can be used to start and operate the vehicle.
Once a Sentry Key

t

is programmed to a vehicle, it cannot

be programmed to any other vehicle.

CAUTION!

Always remove the Sentry Keys

t

from the vehicle

and lock all doors when leaving the vehicle
unattended.

At the time of purchase, the original owner is provided
with a four-digit Personal Identification Number (PIN).
Keep the PIN in a secure location. This number is
required for authorized dealer replacement of keys. Du-
plication of keys may be performed at an authorized
dealer or by following the customer key programming

procedure. This procedure consists of programming a
blank key to the vehicle electronics. A blank key is one
that has never been programmed.

NOTE:

When having the Sentry Key

t

Immobilizer

System serviced, bring all vehicle keys with you to an
authorized dealer.

Customer Key Programming

If you have two valid Sentry Keys

t

, you can program

new Sentry Keys

t

to the system by performing the

following procedure:

1. Cut the additional Sentry Key

t

Transponder blank(s)

to match the ignition switch lock cylinder key code.

2. Insert the first valid key into the ignition switch. Turn
the ignition switch to the ON position for at least three
seconds, but no longer than 15 seconds. Then, turn the
ignition switch to the LOCK position and remove the first
key.

16

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

«
...
16
17
18
19
20
...
»

Summary of Contents for 2008 Avenger




















































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2008 Avenger

Brand: ULTIMATE SPEED Pages: 19

SP200 - QUICKSTART GUIDE 1

Brand: Jabra Pages: 2

BT150 - Headset - Over-the-ear

Brand: Jabra Pages: 2

Brand: Carax Pages: 2

Brand: iDataLink Pages: 99

Brand: Alpine Pages: 8

Brand: Axxess Pages: 8

1997-2007 Dodge Dakota Telescoping Computer Base C-TCB-28

Brand: Havis-Shields Pages: 3

PRIME DESIGN VRR-E-PM21

Brand: Safe Fleet Pages: 12

Brand: Toyota Pages: 636

Sedan CIVIC 2022

Brand: Honda Pages: 701

Brand: GMC Pages: 430

Brand: THIEYE Pages: 88

Brand: Yakima Pages: 12

Brand: Ford Pages: 40

FABIA II TMB PS 035

Brand: Skoda Pages: 16

Brand: TATA Motors Pages: 232

Airgo Active cushion / Comfort

Brand: TOGU Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands