Dodge 2008 Avenger Owner'S Manual Download Page 124 | Manualshive

Page: 124 / 467

background image

WARNING!

•

Adjusting a seat while the vehicle is moving is
dangerous. The sudden movement of the seat
could cause you to lose control. The seat belt might
not be properly adjusted and you could be injured.
Adjust the seat only while the vehicle is parked.

•

Do not ride with the seatback reclined so that the
shoulder belt is no longer resting against your
chest. In a collision you could slide under the seat
belt and be seriously or even fatally injured. Use
the recliner only when the vehicle is parked.

Lumbar Support — If Equipped
This feature allows you to increase or decrease the
amount of lumbar support. The control lever is located
on the outboard side of the driver’s seatback. Turn the
control lever downward to increase and upward to
decrease the desired amount of lumbar support.

Lumbar Support

122

UNDERSTANDING THE FEATURES OF YOUR VEHICLE

«
...
122
123
124
125
126
...
»

Summary of Contents for 2008 Avenger




















































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2008 Avenger

Brand: Camcar Pages: 2

Brand: Yakima Pages: 8

Brand: Metra Electronics Pages: 4

REARSIGHT OnStar 250-8822

Brand: Rostra Pages: 2

Porsche 911 GT3 R

Brand: iRacing Pages: 25

Brand: ideus Pages: 159

Brand: SAN HIMA Pages: 10

Brand: Simplicity Pages: 10

Brand: Kia Pages: 58

Brand: Alphasonik Pages: 8

Brand: Prorack Pages: 14

Brand: Brink Pages: 21

Brand: Lexus Pages: 82

Brand: Calix Pages: 4

Brand: Prorack Pages: 13

Civic Hatch 2017

Brand: Honda Pages: 687

HOLLANDIA 700 - 20 Series

Brand: Webasto Pages: 30

Black Bison Sports Series

Brand: Wald Pages: 7

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands