manualshive.com logo in svg

Dodge 2008 Avenger, Owner'S Manual

The Dodge 2008 Avenger Owner's Manual is your go-to guide for getting the most out of your vehicle. This comprehensive manual covers everything from maintenance and troubleshooting to important safety information. Download your free copy from manualshive.com and enjoy the peace of mind that comes with knowing your vehicle inside out.

Share
Download
background image

BeltAlert

t

will be reactivated if the driver’s seat belt is

unbuckled for more than 10 seconds and the vehicle
speed is greater than 5 mph (8 km/h).

BELTALERT

T

PROGRAMMING

BeltAlert

t

can be enabled or disabled by your authorized

dealer or by following these steps:

NOTE:

The following steps must occur within the first

60 seconds of the ignition switch being turned to the ON
or START position. DaimlerChrysler does not recom-
mend deactivating BeltAlert

t

.

1. Turn the ignition switch to the LOCK position and
buckle the driver’s seat belt.

2. Turn the ignition switch to the ON position and wait
for the Seat Belt Warning Light to turn off.

3. Within 60 seconds of turning the ignition switch to the
ON position, unbuckle and then re-buckle the driver’s
seat belt at least three times within 10 seconds, ending
with the seat belt buckled.

NOTE:

Watch for the Seat Belt Warning Light to turn on

while unbuckling and off while re-buckling the seat belt.
It may be necessary to retract the seat belt partially each
time when unbuckling.

4. Turn the ignition switch to the LOCK position. A
single chime will sound to signify that you have success-
fully completed the programming.

BeltAlert

t

can be reactivated by repeating this procedure.

NOTE:

Although BeltAlert

t

has been deactivated, the

Seat Belt Warning Light will continue to illuminate while
the driver’s seat belt remains unbuckled.

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

49

2

Summary of Contents for 2008 Avenger




















































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2008 Avenger

Jeep 2014 Wrangler Owner'S Manual preview
2014 Wrangler
Brand: Jeep Pages: 673
Uebler F42 Mounting And Operating Instructions preview
F42
Brand: Uebler Pages: 18
Chevrolet Camaro 12000 1968 Series Factory Assembly Instruction Manual preview
Camaro 12000 1968 Series
Brand: Chevrolet Pages: 455
Porsche 911 GT3 - Brochure preview
911 GT3 -
Brand: Porsche Pages: 51
Whispbar K710W Fitting Instructions For Basic Carrier preview
K710W
Brand: Whispbar Pages: 14
Compass 02106 Manual preview
02106
Brand: Compass Pages: 16
Curt Manufacturing 31048 Installation Instructions Manual preview
31048
Brand: Curt Manufacturing Pages: 6
muth signal mirror 2005-2009 Ford Mustang Installation Instruction preview
signal mirror 2005-2009 Ford Mustang
Brand: muth Pages: 9
ULTIMATE SPEED 279746 Assembly And Safety Advice preview
279746
Brand: ULTIMATE SPEED Pages: 6
tams elektronik FCS-4 Manual preview
FCS-4
Brand: tams elektronik Pages: 19
Mazda 2010 MX-5 Miata Specification preview
2010 MX-5 Miata
Brand: Mazda Pages: 8
Toyota RAV-4 2015 Series Owner'S Manual Supplement preview
RAV-4 2015 Series
Brand: Toyota Pages: 50
Waeco Magic Watch MWE-850-4DSM Installation And Operating Manual preview
Magic Watch MWE-850-4DSM
Brand: Waeco Pages: 204
Westfalia 859528 Original Instructions Manual preview
859528
Brand: Westfalia Pages: 10
Yakima Landing Pad 11 Manual preview
Landing Pad 11
Brand: Yakima Pages: 28
Gentex ADVGEN20A Manual preview
ADVGEN20A
Brand: Gentex Pages: 2
Menabo ANTARES KIT+1 Assembly & Instruction Manual preview
ANTARES KIT+1
Brand: Menabo Pages: 8
Seat Arona 2018 Owner'S Manual preview
Arona 2018
Brand: Seat Pages: 372

Brands by name

Popular brands

Load more brands