Dodge 2008 Avenger Owner'S Manual Download Page 31 | Manualshive

Page: 31 / 467

background image

HOW TO USE REMOTE START

All of the following conditions must be met before the
engine will remote start:

•

Shift the gear selector lever into PARK.

•

Doors closed.

•

Hood closed.

•

Trunk closed.

•

Hazard switch off.

•

Brake switch inactive (brake pedal not pressed).

•

Ignition key removed from ignition switch.

•

Battery at an acceptable charge level.

•

RKE PANIC button not pressed.

To Enter Remote Start Mode

Press and release the Remote Start button on
the RKE transmitter twice. The engine will start
and the vehicle will remain in the Remote Start
mode for a 15–minute cycle.

NOTE:

•

For security, power window operation is disabled
when the vehicle is in the Remote Start mode.

•

The engine can be started two consecutive times (two
15–minute cycles) with the RKE transmitter. However,
the ignition switch must be cycled to the ON position
before you can repeat the start sequence for a third
cycle.

To Exit Remote Start Mode Without Driving The
Vehicle
Allow the engine to run for the entire 15-minute cycle.

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

29

2

«
...
29
30
31
32
33
...
»

Summary of Contents for 2008 Avenger




















































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2008 Avenger

Brand: Mazda Pages: 4

Brand: Ultra Start Pages: 8

5TH GEN 4RUNNER

Brand: Victory 4x4 Pages: 5

Brand: Keith Pages: 2

Brand: Trailboss Pages: 8

FIX&GO automatic

Brand: Alfa Romeo Pages: 40

Carpower CAP-20

Brand: Monacor Pages: 2

Brand: StowAway 2 Pages: 2

Brand: T-Mobile Pages: 2

Brand: Bestop Pages: 5

Brand: PowerMadd Pages: 3

Brand: THIEYE Pages: 88

Brand: Abrams Pages: 12

FXX ATM Emulator

Brand: BMW Pages: 5

Brand: Renault Pages: 198

Brand: Vauxhall Pages: 95

Brand: Jaeger Pages: 16

Brand: ROADGEAR Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands