manualshive.com logo in svg

Dodge 2008 Avenger, Owner'S Manual

The Dodge 2008 Avenger Owner's Manual is your go-to guide for getting the most out of your vehicle. This comprehensive manual covers everything from maintenance and troubleshooting to important safety information. Download your free copy from manualshive.com and enjoy the peace of mind that comes with knowing your vehicle inside out.

Share
Download
background image

The dual brake system provides a reserve braking capac-
ity in the event of a failure to a portion of the hydraulic
system. Failure of either half of the dual brake system is
indicated by the Brake Warning Light which will turn on
when the brake fluid level in the master cylinder has
dropped below a specified level.

The light will remain on until the cause is corrected.

NOTE:

The light may flash momentarily during sharp

cornering maneuvers which change fluid level condi-
tions. The vehicle should have service performed, and
the brake fluid level checked.

If brake failure is indicated, immediate repair is neces-
sary.

WARNING!

Driving a vehicle with the brake light on is danger-
ous. Part of the brake system may have failed. It will
take longer to stop the vehicle. You could have an
accident. Have the vehicle checked immediately.

Vehicles equipped with Anti-Lock brakes (ABS), are also
equipped with Electronic Brake Force Distribution (EBD).
In the event of an EBD failure, the Brake Warning Light
will turn on along with the ABS Light. Immediate repair
to the ABS system is required.

The operation of the Brake Warning Light can be checked
by turning the ignition switch from the LOCK position to
the ON position. The light should illuminate for approxi-
mately two seconds. The light should then turn off unless

180

UNDERSTANDING YOUR INSTRUMENT PANEL

Summary of Contents for 2008 Avenger




















































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2008 Avenger

Honda HRM3000 User Manual preview
HRM3000
Brand: Honda Pages: 73
Carefree Slideout Cover Service Manual preview
Slideout Cover
Brand: Carefree Pages: 12
Ultra-tow XTP Series Owner'S Manual preview
XTP Series
Brand: Ultra-tow Pages: 14
Mercedes-Benz 300D 2.5 1990 Owner'S Manual preview
300D 2.5 1990
Brand: Mercedes-Benz Pages: 121
Menabo BIKE PRO Fitting Instructions Manual preview
BIKE PRO
Brand: Menabo Pages: 8
Camtree G-51 Instruction Manual preview
G-51
Brand: Camtree Pages: 5
SnapPad EQ Round Installation Instructions preview
EQ Round
Brand: SnapPad Pages: 5
Thule 1308 Instructions Manual preview
1308
Brand: Thule Pages: 8
Quadratec 12057.0261 Installation Manual preview
12057.0261
Brand: Quadratec Pages: 12
Volvo S90 2018 Quick Manual preview
S90 2018
Brand: Volvo Pages: 42
v.link NAL-PC-HSD Manual preview
NAL-PC-HSD
Brand: v.link Pages: 21
DriveRight 8156OBD Installation Manual preview
8156OBD
Brand: DriveRight Pages: 16
Over Armour Offroad TX-STAMP-4-FC04 Instructions For Installation And Care preview
TX-STAMP-4-FC04
Brand: Over Armour Offroad Pages: 9
Dometic LMC Eriba Nova Service Manual preview
LMC Eriba Nova
Brand: Dometic Pages: 24
Ford F-250 Super Duty 2022 Owner'S Manual preview
F-250 Super Duty 2022
Brand: Ford Pages: 740
Waeco Perfect Fit MBM120 Installation Instructions preview
Perfect Fit MBM120
Brand: Waeco Pages: 3
Or-Fab HD Bumper Installation Instructions preview
HD Bumper
Brand: Or-Fab Pages: 4
Kia Optima 2004 Owner'S Manual preview
Optima 2004
Brand: Kia Pages: 233

Brands by name

Popular brands

Load more brands