Dodge 2008 Avenger Owner'S Manual Download Page 242

Page: 242 / 467

•

The LCD screen swings up from the rear of the armrest
to allow the rear seat passenger(s) to view the display.

NOTE:

Close the armrest after the LCD screen has been

raised to its viewing position.

•

The touch screen radio and DVD player controls allow
front seat operation for easy setup in the case of
younger rear seat passengers.

•

A battery-powered infrared remote control snaps into
a molded compartment in the center console armrest
upper storage bin.

VES

Video Screen

VES

Remote Control

240

UNDERSTANDING YOUR INSTRUMENT PANEL

Summary of Contents for 2008 Avenger




















































































































































































































































































































































































































































































Search results

Summary of Contents for 2008 Avenger

Reviews:

Related manuals for 2008 Avenger

Brands by name

Popular brands

Dodge 2008 Avenger, Owner'S Manual

Search results

Summary of Contents for 2008 Avenger

Reviews:

Related manuals for 2008 Avenger

Brands by name

Popular brands