manualshive.com logo in svg

Dodge 2008 Avenger, Owner'S Manual

The Dodge 2008 Avenger Owner's Manual is your go-to guide for getting the most out of your vehicle. This comprehensive manual covers everything from maintenance and troubleshooting to important safety information. Download your free copy from manualshive.com and enjoy the peace of mind that comes with knowing your vehicle inside out.

Share
Download
background image

The bar code allows a computer scanner to read the
Vehicle Identification Number (VIN).

Gross Vehicle Weight Rating (GVWR)

The GVWR is the total allowable weight of your vehicle.
This includes driver, passengers, and cargo. The total
load must be limited so that you do not exceed the
GVWR.

Gross Axle Weight Rating (GAWR)

The GAWR is the maximum capacity of the front and rear
axles. Distribute the load over the front and rear axles
evenly. Make sure that you do not exceed either front or
rear GAWR.

WARNING!

Because the front wheels steer the vehicle, it is
important that you do not exceed the maximum front
or rear GAWR. A dangerous driving condition can
result if either rating is exceeded. You could lose
control of the vehicle and have an accident.

Overloading

The load carrying components (axle, springs, tires,
wheels, etc.) of your vehicle will provide satisfactory
service as long as you do not exceed the GVWR and front
and rear GAWR.

The best way to figure out the total weight of your
vehicle is to weigh it when it is fully loaded and ready for
operation. Weigh it on a commercial scale to insure that it
is not over the GVWR.

332

STARTING AND OPERATING

Summary of Contents for 2008 Avenger




















































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2008 Avenger

Eaton Green Motion Building Quick Start Manual preview
Green Motion Building
Brand: Eaton Pages: 12
Porsche Carrera GT Manual preview
Carrera GT
Brand: Porsche Pages: 192
Prorack K383 Fitting Instructions Manual preview
K383
Brand: Prorack Pages: 14
Buick 2005 Terraza Owner'S Manual preview
2005 Terraza
Brand: Buick Pages: 428
SuperATV AAB-P-RZR900-K2-001 Installation Instructions preview
AAB-P-RZR900-K2-001
Brand: SuperATV Pages: 3
E&G Classics 1398-0502-09 Instruction Manual preview
1398-0502-09
Brand: E&G Classics Pages: 2
E&G Classics 1409-0102-10 Installation Instructions preview
1409-0102-10
Brand: E&G Classics Pages: 3
Hummer HX-T Owner'S Manual preview
HX-T
Brand: Hummer Pages: 31
POOL-LINE 110085 Assembly Instructions preview
110085
Brand: POOL-LINE Pages: 2
Pontiac 2007 G6 Owner'S Manual preview
2007 G6
Brand: Pontiac Pages: 486
Dodge Charger SRT 392 2017 Operating Information Manual preview
Charger SRT 392 2017
Brand: Dodge Pages: 576
Lexus LS 500h 2022 Owner'S Manual, Quick Manual preview
LS 500h 2022
Brand: Lexus Pages: 108
Subaru 1999 Legacy Owner'S Manual preview
1999 Legacy
Brand: Subaru Pages: 399
Mazda Auto-Dimming Mirror User Manual preview
Auto-Dimming Mirror
Brand: Mazda Pages: 2
Kuda-Phonebase 291790 Installation Instruction preview
291790
Brand: Kuda-Phonebase Pages: 3
PIE FRDN/PC-POD2 Application And Installation Instructions preview
FRDN/PC-POD2
Brand: PIE Pages: 2
walser Proguard 100021 User Instructions preview
Proguard 100021
Brand: walser Pages: 12
DV8 FBBR-03 Installation Manual preview
FBBR-03
Brand: DV8 Pages: 11

Brands by name

Popular brands

Load more brands