Dodge 2008 Avenger Owner'S Manual Download Page 164 | Manualshive

Page: 164 / 467

background image

The cooling bin will hold up to four, standing, 12 ounce,
beverage cans. The cooler bin is also equipped with a soft
molded liner that is removable for easy cleaning.

Inside the bin is a vent which, when opened, allows
either air conditioned or fresh air to flow into the storage
bin. Depending on ambient temperature and A/C set-
ting, the bin can keep beverages cool.

For the Cooler Storage Bin to operate properly, door must
remain closed while vehicle is in operation.

Shut off the beverage cooler when not in use, by closing
the vent inside. This will prevent cool air from entering
the passenger compartment when in heat mode.

NOTE:

The use of the Beverage Cooler Storage Bin is for

non-perishable beverages only.

The Glove Compartment is located beneath the beverage
bin. The glove compartment door swings downward for
easy access.

Glove Compartment Access

162

UNDERSTANDING THE FEATURES OF YOUR VEHICLE

«
...
162
163
164
165
166
...
»

Summary of Contents for 2008 Avenger




















































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2008 Avenger

Brand: JETBAG Pages: 44

Brand: Jeep Pages: 322

Brand: Jeep Pages: 341

Brand: Jeep Pages: 310

Brand: Jeep Pages: 189

Brand: Jeep Pages: 26

Brand: Jeep Pages: 21

Brand: Fabbri Pages: 4

Brand: BGS technic Pages: 5

Brand: Oldsmobile Pages: 344

Brand: ABL Pages: 66

Brand: Renault Pages: 238

Brand: AEM Pages: 27

Sedan CIVIC 2022

Brand: Honda Pages: 701

2011 A3 Sportback

Brand: Audi Pages: 29

Brand: NavLinkz Pages: 23

Brand: Hama Pages: 13

T13 Outback Frontal Protection System

Brand: T.J.M. Pages: 18

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands