Dodge 2008 Avenger Owner'S Manual Download Page 130 | Manualshive

Page: 130 / 467

background image

Then lift the secondary latch located under the front edge
of the hood, near the center and raise the hood.

Use the hood prop rod to secure the hood in the open
position. Place the upper end of the prop rod in the hole
on the left underside of the hood.

Before closing the hood, make sure to stow the prop rod
in its proper location. To prevent possible damage, do not
slam the hood to close it. Use a firm downward push at
the center of the hood to ensure that both latches engage.

Hood Safety Catch

Hood Prop Rod Hole Location

128

UNDERSTANDING THE FEATURES OF YOUR VEHICLE

«
...
128
129
130
131
132
...
»

Summary of Contents for 2008 Avenger




















































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2008 Avenger

Brand: Velleman Pages: 6

Brand: Chevrolet Pages: 376

Brand: Mazda Pages: 15

Brand: Kuda Pages: 3

Brand: Flash Cover Pages: 2

Brand: Renault Pages: 340

Brand: Ecco Pages: 12

Brand: v.LOGiC Pages: 22

Brand: Jaeger Pages: 11

Brand: cam Pages: 28

Brand: r.LiNK Pages: 21

Brand: v.link Pages: 19

Brand: Honda Pages: 268

HOLLANDIA 700 - 20 Series

Brand: Webasto Pages: 30

Brand: Carbest Pages: 64

Brand: Honda Pages: 2

Brand: Metra Electronics Pages: 17

Brand: AUTOTECH Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands