![background image](http://html1.mh-extra.com/html/ecco/5545a/5545a_installation-and-operating-instructions-manual_530677001.webp)
5545/5550 Series - Reflex™ LED Microbars provide a
compact yet powerful warning solution that offers the
flexibility of either permanent, high-bond tape (HBT), or
vacuum-magnet mounting. All models feature 12-24 VDC
operation and use LED technology to maximize light out
-
put. Multiple flash patterns are available including double,
quad quint, rotate and random.
Page 1 of 4
Specifications:
Size: 5545X, 5545XX
10” x 7” x 2”
5550X, 5550XX
5550XXX
5545X-HBT, 5545XX-HBT 10” x 7” x 2.5”
5550X-HBT, 5550XX-HBT
5550XXX-HBT
5545X-VM, 5545XX-VM 10” x 7” x 3”
5550X-VM, 5550XX-VM
5550XXX-VM
Input Voltage: 12 to 24 VDC systems
Weight:
Current Draw:
5545: 1.48 Amps Maximum
Maximum power consumption: 18.9 watts
5550: 3.8 Amps Maximum
Maximum power consumption: 48.6 watts
Flash Rate:
See Flash Pattern Chart
Temp. Range:
-30ºC to +50ºC
1. Proper installation combined with operator training in the use, care, and maintenance of emergency warning devices are essential to ensure
the safety of you and those you are seeking to protect.
2. Exercise caution when working with live electrical connections.
3. This product must be properly grounded. Inadequate grounding and/or shorting of electrical connections can cause high current arcing,
which can cause personal injury and/or severe vehicle damage, including fire.
4. Proper placement and installation are vital to the performance of this warning device. Install this product so that output performance of the
system is maximized and the controls are placed within convenient reach of the operator so that s/he can operate the system without losing
eye contact with the roadway.
5. Do not install this product or route any wires in the deployment area of an air bag. Equipment mounted or located in an air bag deployment
area may reduce the effectiveness of the air bag or become a projectile that could cause serious personal injury or death. Refer to the
vehicle owner’s manual for the air bag deployment area. It is the responsibility of the user/operator to determine a suitable mounting location
ensuring the safety of all passengers inside the vehicle particularly avoiding areas of potential head impact.
6. It is the responsibility of the vehicle operator to ensure during use that all features of this product work correctly. In use, the vehicle operator
should ensure the projection of the warning signal is not blocked by vehicle components (i.e., open trunks or compartment doors), people,
vehicles or other obstructions.
7. The use of this or any other warning device does not ensure all drivers can or will observe or react to a warning signal. Never take the right-
of-way for granted. It is your responsibility to be sure you can proceed safely before entering an intersection, driving against traffic, respond-
ing at a high rate of speed, or walking on or around traffic lanes.
8. This equipment is intended for use by authorized personnel only. The user is responsible for understanding and obeying all laws regarding
warning signal devices. Therefore, the user should check all applicable city, state, and federal laws and regulations. The manufacturer as-
sumes no liability for any loss resulting from the use of this warning device.
Do not install and/or operate this safety product unless you have read and understand the safety information
contained
Failure to install or use this product according to manufacturer’s recommendations may result in property damage, serious injury, and/or death to
those you are seeking to protect!
!
WARNING!
Installation & Mounting:
Important!
This unit is a safety device, and it must be
connected to its own separate, fused power point to assure
its continued operation should any other electrical accessory
fail.
Carefully remove the Microbar and place it on a flat surface.
Examine the unit for transit damage, and locate all parts. If dam
-
age is found, or parts are missing, contact the transit company or
ECCO. Do not use damaged or broken parts.
Installation and Operation Instructions
5500 Series LED Microbars
Mount
5545
5550
Permanent Mount
approx. 1.8 lbs
approx. 2.0 lbs
HBT Mount
approx 2.5 lbs
approx. 4.0 lbs
Vacuum-Magnet Mount
approx. 3.0 lbs
approx. 4.3 lbs
Permanent Mounting:
1. Select the desired location on a flat surface for the
Microbar to be mounted. The visibility of the flash and
ease of wiring access should be taken into
consideration in the selection of the mounting location.
2. Remove lens screws, then remove lens. Use the four holes in the
corners of the base to mark the mounting hole locations.
3. Drill the holes using a 7/32” drill size.
4. A fifth hole may be drilled for wire access.
5. Connect the power wires as shown in the wiring section
(see Figure 6).
6. Mount the microbar with M5 hardware provided.
Caution:
When drilling into any vehicle surface, make sure the area
is free from any electrical wires, fuel lines, vehicle upholstery, etc. that
could be damaged
Important!
Disable power before wiring up the Microbar.