manualshive.com logo in svg

Dodge 2008 Avenger, Owner'S Manual

The Dodge 2008 Avenger Owner's Manual is your go-to guide for getting the most out of your vehicle. This comprehensive manual covers everything from maintenance and troubleshooting to important safety information. Download your free copy from manualshive.com and enjoy the peace of mind that comes with knowing your vehicle inside out.

Share
Download
background image

TOWING WITHOUT POWER — OVERRIDE
TRANSAXLE INTERLOCK SYSTEM

Special care must be taken when the vehicle is towed
with the ignition in the LOCK position. A dolly should be
used under the front wheels if the rear wheels are raised.
Proper towing equipment is necessary to prevent dam-
age to the vehicle.

Battery power is required to release the brake/transaxle
interlock system. There is an override system that allows
you to shift out of PARK in case of loss of power. To
activate the override system:

•

Firmly apply the parking brake.

•

Insert the ignition key and rotate it to the ON position.

•

Remove the cupholder liner.

•

Insert a key, screwdriver, or similar object into the
front hole then push and hold the manual override
release lever forward.

•

While holding the release lever forward, move the
shift lever from PARK to NEUTRAL.

•

Release the override.

364

WHAT TO DO IN EMERGENCIES

Summary of Contents for 2008 Avenger




















































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2008 Avenger

Jeep Compass Overview Manual preview
Compass
Brand: Jeep Pages: 25
Jetter JX3-BN-CAN Manual preview
JX3-BN-CAN
Brand: Jetter Pages: 4
K&K M5700N Manual preview
M5700N
Brand: K&K Pages: 8
K&K M4700 Manual preview
M4700
Brand: K&K Pages: 20
K&K M3500N Manual preview
M3500N
Brand: K&K Pages: 6
K&K M2500 Manual preview
M2500
Brand: K&K Pages: 3
K&K M1500 Manual preview
M1500
Brand: K&K Pages: 3
Parrot CK3300 Setup Information Manual preview
CK3300
Brand: Parrot Pages: 19
Parrot Minikit+ Quick Start Manual preview
Minikit+
Brand: Parrot Pages: 88
Parrot Minikit+ Information Sheet preview
Minikit+
Brand: Parrot Pages: 2
Parrot CK3100 LCD Specifications preview
CK3100 LCD
Brand: Parrot Pages: 2
Parrot CK 3000 Evolution Installation Notes preview
CK 3000 Evolution
Brand: Parrot Pages: 8
Parrot CK 3000 Evolution User Manual preview
CK 3000 Evolution
Brand: Parrot Pages: 106
Paccar DAF POWERCHOICE 250A Installation Manual preview
DAF POWERCHOICE 250A
Brand: Paccar Pages: 20
Carcomm CNM-71 Quick Start Manual preview
CNM-71
Brand: Carcomm Pages: 2
Whispbar K392W Fitting Instructions For Basic Carrier preview
K392W
Brand: Whispbar Pages: 14
REVCAMUK MON16AHD Instructions preview
MON16AHD
Brand: REVCAMUK Pages: 4
Dakota Digital MCL-7000 Series Quick Start Manual preview
MCL-7000 Series
Brand: Dakota Digital Pages: 2

Brands by name

Popular brands

Load more brands