Infineon Technologies TC1784 Скачать руководство пользователя страница 529 | Manualshive

Страница: 529 / 2350

Infineon Technologies TC1784 Скачать руководство пользователя страница 529

TC1784

Data Access Overlay (OVC)

User´s Manual

6-8

V1.1, 2011-05

OVC, V1.19

Note: Accesses to free/not used register addresses within the OVC address space are

not executed and not serviced with a bus error trap.

Register Descriptions

For each of the 16 overlay memory blocks (indicated by index x), three registers control
the overlay operation and the memory selection:
•

The Overlay Target Address Register OTARx, which holds the base address of the
memory block in internal Flash, in external memory or in the OLDA memory being
overlaid (and being compared with original data address).

•

The Redirected Address Base Register RABRx, which holds the base address of the
overlay memory to be used (with fixed address bits) and of the overlay memory block
within the overlay memory, and some control bits.

•

The Overlay Mask Register OMASKx, which determines which bits (from RABRx)
are used for the base address (of overlay memory and block) and which bits (of
original data address) are directly used as offset within the block (remaining
unchanged).

Additionally, for general overlay control the register OCON is provided.
All overlay block and control registers are reset to their default values with the application
reset. A special debug reset is not considered.

Note:

All overlay block control registers have different definitions for overlay blocks in
internal OVRAM (RABRx.IEMS=0), and overlay blocks in EMEM or external
memory (RABRx.IEMS=1 or RABRx.EXOMS=1). Therefore, in the following, two
(RABRx: three) different definitions are provided for the same register.

Table 6-2

Registers Overview

Register

1)

Short
Name

1) The OVC register short names are extended with the module name prefix “OVC_”.

Register Long Name

Offset
Address

Access

Mode

2)

2) Symbol U: Access permitted in User Mode 0 or 1

Symbol SV: Access permitted in Supervisor Mode

Descript-
ion see

Read Write

OTARx

Overlay Target Address Register x
(x = 0-15)

0024

H

+

x

∗

C

H

U, SV SV

RABRx

Redirected Address Base Register x
(x = 0-15)

0020

H

+

x

∗

C

H

U, SV SV

OMASKx

Overlay Mask Register x
(x = 0-15)

0028

H

+

x

∗

C

H

U, SV SV

OCON

Overlay Control Register

00E0

H

U,

SV SV

«
...
527
528
529
530
531
...
»

Содержание TC1784















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды