Thermo Scientific Partisol 2000i Instruction Manual Download | Manualshive

Page: 321 / 403

background image

Thermo Fisher Scientific

Partisol 2000

i

and Partisol 2000

i

-D Instruction Manual

C-1

Appendix C

MODBUS Protocol

This appendix provides a description of the MODBUS Protocol Interface
and is supported both over RS-232/485 (RTU protocol) as well as TCP/IP
over Ethernet.

The MODBUS Commands that are implemented are explained in detail in
this document. The MODBUS protocol support for the Sampler enables
the user to perform the functions such as reading the various measurements
and other analog values or variables, reading the status of the digital
outputs, and to triggering or simulating the activation of a digital input to
the Sampler. This is achieved by using the following supported MODBUS
commands.

For details of the Partisol 2000

i

and 2000

i

-D MODBUS Protocol

specification, see the following topics:

●

“

Serial Communication Parameters

” on page

C-1

●

“

TCP Communication Parameters

” on page

C-2

●

“

Application Data Unit Definition

” on page

C-2

●

“

Function Codes

” on page

C-3

●

“

MODBUS Addresses Supported

” on page

C-8

Additional information on the MODBUS protocol can be obtained at

http://www.modbus.org

. References are from MODBUS Application

Protocol Specification V1.1a MODBUS-IDA June 4, 2004.

The following are the communication parameters that are used to configure
the serial port of the

i

Series to support MODBUS RTU protocol.

Number of Data bits : 7 or 8

Number of Stop bits : 1 or 2

Parity

: None, Odd, or Even

Data rate

: 1200 to 115200 Baud (9600 is default)

Serial Communication

Parameters

«
...
319
320
321
322
323
...
»

Summary of Contents for Partisol 2000i




















































































































































































































































































































































































































Reviews:

No comments

Related manuals for Partisol 2000i

DigitalFlow XMT868i

Brand: Panametrics Pages: 74

Brand: 3M Pages: 2

Brand: 3M Pages: 16

Brand: Datavideo Pages: 26

Brand: Datcon Pages: 84

Brand: VELOCICALC Pages: 6

Brand: Panametrics Pages: 68

Goldmann AT 870

Brand: Haag-Streit Pages: 20

Brand: Fender Pages: 20

Brand: DAKOTA ULTRASONICS Pages: 50

Brand: Jamar Pages: 4

Brand: PCB Piezotronics Pages: 15

Brand: Palstar Pages: 15

Brand: Technoline Pages: 1

Brand: BD Sensors Pages: 4

Brand: Roland Pages: 2

Brand: Karman Pages: 2

Brand: Interacoustics Pages: 54

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands