Thermo Scientific Partisol 2000i Instruction Manual Download

Page: 289 / 403

C-Link Protocol Commands

Measurements

Thermo Fisher Scientific

Partisol 2000

and Partisol 2000

-D Instruction Manual

B-9

filter2 temp

This command reports the value for the filter2 temperature in degrees C.

Send:

filter2

temp

Receive:

filter2 temp 19.9

flow actual

This command reports the value for the actual flow (filter 1) in L/min.

Send:

flow

actual

Receive: flow

actual

14.90

flow2 actual

This command reports the value for the actual flow (filter 2) in L/min.

Send:

flow2

actual

Receive:

flow2 actual 2.4

flow mass

This command reports the value for the mass flow (filter 1) in L/min.

Send:

flow

mass

Receive: flow

mass

12.90

flow2 mass

This command reports the value for the mass flow (filter 2) in L/min.

Send:

flow2

mass

Receive:

flow2 mass 2.40

flow std

This command reports the value for the std flow (filter 1) in L/min.

Send:

flow

std

Receive: flow

mass

12.20

flow2 std

This command reports the value for the std flow (filter 2) in L/min.

Send:

flow2

std

Receive:

flow2 mass 2.40

wind dir

This command reports the wind direction in degrees (0-360).

Send:

wind

dir

Receive:

wind dir 269

wind speed

This command reports the wind speed in km/h.

Summary of Contents for Partisol 2000i




















































































































































































































































































































































































































Search results

Summary of Contents for Partisol 2000i

Reviews:

Related manuals for Partisol 2000i

Brands by name

Popular brands

Thermo Scientific Partisol 2000i, Instruction Manual

Search results

Summary of Contents for Partisol 2000i

Reviews:

Related manuals for Partisol 2000i

Brands by name

Popular brands