manualshive.com logo in svg

Renesas SH7706 Series, Hardware Manual

The Renesas SH7706 Series is a high-performance microcontroller designed for a wide range of applications. To maximize the potential of this product, it is crucial to have access to its comprehensive "Hardware Manual". This manual can be easily downloaded for free from manualshive.com, providing users with detailed instructions and specifications for optimal usage.

Share
Download
background image

Section 7   User Break Controller

Rev. 5.00  May 29, 2006  page 141 of 698

REJ09B0146-0500

7.2

Register Description

The UBC has the following registers. Refer to section 23, List of Registers, for more details of the
addresses and access sizes.

•

 

Break address register A (BARA)

•

 

Break address mask register A (BAMRA)

•

 

Break bus cycle register A (BBRA)

•

 

Break address register B (BARB)

•

 

Break address mask register B (BAMRB)

•

 

Break bus cycle register B (BBRB)

•

 

Break data register B (BDRB)

•

 

Break data mask register B (BDMRB)

•

 

Break control register (BRCR)

•

 

Execution count break register (BETR)

•

 

Branch source register (BRSR)

•

 

Branch destination register (BRDR)

•

 

Break ASID register A (BASRA)

•

 

Break ASID register B (BASRB)

7.2.1

Break Address Register A (BARA)

BARA is a 32-bit read/write register. BARA specifies the address used as a break condition in
channel A.

Bit

Bit Name

Initial Value

R/W

Description

31 to 0

BAA31 to
BAA0

All 0

R/W

Break Address

Stores the address on the LAB or IAB that
specifies break conditions of channel A.

Summary of Contents for SH7706 Series














































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SH7706 Series

GE MDS SD Series Setup Manual preview
MDS SD Series
Brand: GE Pages: 4
Aastra CNX Product Brief preview
CNX
Brand: Aastra Pages: 2
CSS SafetyNet Quick Install Manual preview
SafetyNet
Brand: CSS Pages: 2
MiLAN E-MCC-1600 Install Manual preview
E-MCC-1600
Brand: MiLAN Pages: 1
Symantec PacketShaper PS-S200 Quick Start Manual preview
PacketShaper PS-S200
Brand: Symantec Pages: 2
Lanner NCA-4035 User Manual preview
NCA-4035
Brand: Lanner Pages: 109
Avolites Titan One Quick Start Manual preview
Titan One
Brand: Avolites Pages: 24
Lanner ICS-P570 User Manual preview
ICS-P570
Brand: Lanner Pages: 63
Ericsson Marconi OMS 1200 Product Description preview
Marconi OMS 1200
Brand: Ericsson Pages: 136
ebm-papst D3G146-LT13-30 Operating Instructions Manual preview
D3G146-LT13-30
Brand: ebm-papst Pages: 11
YASKAWA PG-Z2 Instructions Manual preview
PG-Z2
Brand: YASKAWA Pages: 15
DAD DXZ48 User Manual preview
DXZ48
Brand: DAD Pages: 16
Addonics Technologies ADSA2 Installation Manual preview
ADSA2
Brand: Addonics Technologies Pages: 1
Jaycar Electronics Duinotech Lilypad Plus XC3920 Quick Start preview
Duinotech Lilypad Plus XC3920
Brand: Jaycar Electronics Pages: 2
3Com 3C433279A Release Note preview
3C433279A
Brand: 3Com Pages: 12
Hanwha Techwin Wisenet PRN-6400DB4 User Manual preview
Wisenet PRN-6400DB4
Brand: Hanwha Techwin Pages: 125
JETWAY LI22 Series User Manual preview
LI22 Series
Brand: JETWAY Pages: 63
Renesas Emulation Memory Board R0E330850MSRC0 User Manual preview
Emulation Memory Board R0E330850MSRC0
Brand: Renesas Pages: 4

Brands by name

Popular brands

Load more brands