Renesas SH7706 Series Hardware Manual Download | Manualshive

Page: 134 / 749

background image

Section 4 Exception Processing

Rev. 5.00 May 29, 2006 page 86 of 698
REJ09B0146-0500

Exception Type

Exception Event

Exception Code

Nonmaskable interrupt

H'1C0

H-UDI interrupt

H'5E0

General interrupt requests

External hardware interrupts:

IRL3–IRL0

= 0000

H'200

IRL3–IRL0

= 0001

H'220

IRL3–IRL0

= 0010

H'240

IRL3–IRL0

= 0011

H'260

IRL3–IRL0

= 0100

H'280

IRL3–IRL0

= 0101

H'2A0

IRL3–IRL0

= 0110

H'2C0

IRL3–IRL0

= 0111

H'2E0

IRL3–IRL0

= 1000

H'300

IRL3–IRL0

= 1001

H'320

IRL3–IRL0

= 1010

H'340

IRL3–IRL0

= 1011

H'360

IRL3–IRL0

= 1100

H'380

IRL3–IRL0

= 1101

H'3A0

IRL3–IRL0

= 1110

H'3C0

Note:

Exception codes H'120, H'140, and H'3E0 are reserved.

4.1.5

Exception Request and BL Bit

If a general exception event occurs when the BL bit in SR is 1, the CPU's internal registers are set
to their post-reset state, other module registers retain their contents prior to the general exception,
and a branch is made to the same address (H'A0000000) as for a reset.

If a general interrupt occurs when BL

=

1, the request is masked (held pending) and not accepted

until the BL bit is cleared to 0 by software. For reentrant exception processing, the SPC and SSR
must be saved and the BL bit in SR cleared to 0.

4.1.6

Returning from Exception Processing

The RTE instruction is used to return from exception processing. When RTE is executed, the SPC
value is set in the PC, and the SSR value in SR, and the return from exception processing is
performed by branching to the SPC address.

«
...
132
133
134
135
136
...
»

Summary of Contents for SH7706 Series














































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SH7706 Series

Brand: Palo Alto Network Pages: 56

FrameSaver 9120

Brand: Paradyne Pages: 2

LightSpeed Appliance QLS250

Brand: Quantum Pages: 12

HAWA-Frontside 60/B

Brand: hawa Pages: 28

Brand: u-blox Pages: 29

PISO-725 Series

Brand: ICP DAS USA Pages: 8

Brand: Infoblox Pages: 13

SOUL CALIBUR II

Brand: NAMCO Pages: 26

Brand: Pilz Pages: 12

Brand: ICP DAS USA Pages: 8

GPX-N 1080Ti-M23

Brand: Alphacool Pages: 4

Brand: Crown Pages: 7

Dablet DVP 5000

Brand: DarbeeVision Pages: 10

Brand: VIA Technologies Pages: 2

Brand: Alcatel-Lucent Pages: 8

Schoeps electret

Brand: VAMISOUND Pages: 15

RouterBOARD 711-5HnD

Brand: MikroTik Pages: 2

Brand: Solid State Logic Pages: 30

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands