Renesas SH7706 Series Hardware Manual Download | Manualshive

Page: 211 / 749

background image

Section 8 Bus State Controller (BSC)

Rev. 5.00 May 29, 2006 page 163 of 698

REJ09B0146-0500

Section 8 Bus State Controller (BSC)

The bus state controller (BSC) divides physical address space and output control signals for
various types of memory and bus interface specifications. BSC functions enable this LSI to link
directly with DRAM, synchronous DRAM, SRAM, ROM, and other memory storage devices
without an external circuit. The BSC also allows direct connection to PCMCIA interfaces,
simplifying system design and allowing high-speed data transfers in a compact system.

Figure 8.1 shows the block diagram of the BSC.

8.1

Feature

The BSC has the following features:

•

Physical address space is divided into six areas



A maximum 64 Mbytes for each of the six areas, 0, 2 to 6



Area bus width can be selected by register (area 0 is set by external pin)



Wait states can be inserted using the

WAIT

pin



Wait state insertion can be controlled through software. Register settings can be used to
specify the insertion of 1 to 10 cycles independently for each area (1 to 38 cycles for areas
5 and 6 and the PCMCIAT interface only)



The type of memory connected can be specified for each area, and control signals are
output for direct memory connection



Wait cycles are automatically inserted to avoid data bus conflict for continuous memory
accesses to different areas or writes directly following reads of the same area

•

Direct interface to synchronous DRAM (except when clock ratio becomes I

φ

:B

φ

= 1:1)



Multiplexes row/column addresses according to synchronous DRAM capacity



Supports burst operation



Supports bank active mode



Has both auto-refresh and self-refresh functions



Controls timing of synchronous DRAM direct-connection control signals according to
register setting

•

Burst ROM interface



Insertion of wait states controllable through software



Register setting control of burst transfers

•

PCMCIA interface



Insertion of wait states controllable through software

«
...
209
210
211
212
213
...
»

Summary of Contents for SH7706 Series














































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SH7706 Series

Brand: LAWO Pages: 154

Brand: Freescale Semiconductor Pages: 921

RUGGEDMAX WIN7000

Brand: RuggedCom Pages: 42

Brand: Zoom Pages: 88

PBE-5AC-300-ISO

Brand: Ubiquiti Pages: 28

Brand: Omron Pages: 13

Brand: Lanner Pages: 59

Brand: C&T Solution Pages: 129

Brand: Arbor Technology Pages: 8

FastTrak TX4000

Brand: Promise Technology Pages: 76

Brand: Supero Pages: 53

Brand: Keil Pages: 68

Advanced Flame 1.0

Brand: Eastern Voltage Research Pages: 12

Brand: ADTRAN Pages: 9

Brand: Altera Pages: 40

Brand: Milesight Pages: 15

Brand: VIA Technologies Pages: 25

Brand: ICOP Technology Pages: 42

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands