manualshive.com logo in svg

Renesas SH7706 Series, Hardware Manual

The Renesas SH7706 Series is a high-performance microcontroller designed for a wide range of applications. To maximize the potential of this product, it is crucial to have access to its comprehensive "Hardware Manual". This manual can be easily downloaded for free from manualshive.com, providing users with detailed instructions and specifications for optimal usage.

Share
Download
background image

Section 9   Direct Memory Access Controller (DMAC)

Rev. 5.00  May 29, 2006  page 296 of 698
REJ09B0146-0500

CMCNT Count Timing

One of four clocks (P

φ

/4, P

φ

/8, P

φ

/16, P

φ

/64) obtained by dividing the peripheral clock (P

φ

) can

be selected by the CKS1 and CKS0 bits of the CMCSR. Figure 9.28 shows the timing.

N+1

Peripheral clock (P

φ

)

CMT clock

CMCNT0 input clock

CMCNT0

N-1

N

Figure 9.28   Count Timing

Compare Match Flag Set Timing

The CMF bit of the CMCSR register is set to 1 by the compare match signal generated when the
CMCOR register and the CMCNT counter match. The compare match signal is generated upon
the final state of the match (timing at which the CMCNT counter matching count value is
updated). Consequently, after the CMCOR register and the CMCNT counter match, a compare
match signal will not be generated until a CMCNT counter input clock occurs. Figure 9.29 shows
the CMF bit set timing.

Summary of Contents for SH7706 Series














































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SH7706 Series

Salusfin SF-930EU User'S Installation Manual preview
SF-930EU
Brand: Salusfin Pages: 6
Dahua NVR2104-S2 Quick Start Manual preview
NVR2104-S2
Brand: Dahua Pages: 6
Supermicro SuperServer 5019S-L User Manual preview
SuperServer 5019S-L
Brand: Supermicro Pages: 61
Time domain PulsON 440 Datasheet And User Manual preview
PulsON 440
Brand: Time domain Pages: 64
Sennheiser Surround Dongle User Manual preview
Surround Dongle
Brand: Sennheiser Pages: 18
EK-Quantum Momentum ROG Strix X570-E D-RGB User Manual preview
Momentum ROG Strix X570-E D-RGB
Brand: EK-Quantum Pages: 10
Thermalright AXP-100H MUSCLE Manual preview
AXP-100H MUSCLE
Brand: Thermalright Pages: 36
pivotal COMMWARE ECHO 5G How To Set Up preview
COMMWARE ECHO 5G
Brand: pivotal Pages: 2
AOpen VA1000 Lite2 User Manual And Technical Manual preview
VA1000 Lite2
Brand: AOpen Pages: 18
ZALMAN CNPS11X Extreme User Manual preview
CNPS11X Extreme
Brand: ZALMAN Pages: 12
Arduino ABX00061 Reference Manual preview
ABX00061
Brand: Arduino Pages: 25
Divio SRA311-008P8 Series Installation Manual preview
SRA311-008P8 Series
Brand: Divio Pages: 4
AMX AXB-PSCV Dimensional Drawing preview
AXB-PSCV
Brand: AMX Pages: 1
ZyXEL Communications PK5000Z How To Configure preview
PK5000Z
Brand: ZyXEL Communications Pages: 3
Supero AOC-1UIPMI-B User Manual preview
AOC-1UIPMI-B
Brand: Supero Pages: 53
SONIX MP5S Plus Writer Quick Manual preview
MP5S Plus Writer
Brand: SONIX Pages: 23
Intel SRCSASPH16I - RAID Controller Hardware Manual preview
SRCSASPH16I - RAID Controller
Brand: Intel Pages: 28
ZALMAN OPTIMA II CNPS10X User Manual preview
OPTIMA II CNPS10X
Brand: ZALMAN Pages: 20

Brands by name

Popular brands

Load more brands