manualshive.com logo in svg

Renesas SH7706 Series, Hardware Manual

The Renesas SH7706 Series is a high-performance microcontroller designed for a wide range of applications. To maximize the potential of this product, it is crucial to have access to its comprehensive "Hardware Manual". This manual can be easily downloaded for free from manualshive.com, providing users with detailed instructions and specifications for optimal usage.

Share
Download
background image

Section 10   Clock Pulse Generator (CPG)

Rev. 5.00  May 29, 2006  page 303 of 698

REJ09B0146-0500

Section 10   Clock Pulse Generator (CPG)

The clock pulse generator (CPG) supplies all clocks to the processor and controls the power-down
modes. A block diagram of the clock pulse generator is shown in figure 10.1.

10.1

Feature

The CPG has the following features:

•

 

Four clock modes: Selection of 4 clock modes for different frequency ranges, power
consumption, direct crystal input, and external clock input are available.

•

 

Three clocks generated independently: An internal clock for the CPU, cache, and TLB (I

φ

); a

peripheral clock (P

φ

) for the on-chip supporting modules; and a bus clock (CKIO) for the

external bus interface.

•

 

Frequency change function: CPU and peripheral clock frequencies can be changed
independently using the PLL circuit and divider circuit within the CPG. Frequencies are
changed by software using frequency control register (FRQCR) settings.

•

 

Power-down mode control: The clock can be stopped for sleep mode and software standby
mode and specific modules can be stopped using the module standby function.

Summary of Contents for SH7706 Series














































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SH7706 Series

AMD SB710 User Manual preview
SB710
Brand: AMD Pages: 20
ICP DAS USA PISO-725 Series Quick Start Manual preview
PISO-725 Series
Brand: ICP DAS USA Pages: 8
IEI Technology HPE-6S2 Quick Installation Manual preview
HPE-6S2
Brand: IEI Technology Pages: 3
Eneo PNR-5304 Quick Installation Manual preview
PNR-5304
Brand: Eneo Pages: 68
SAB SABVISION NVR32 Quick Start Manual preview
SABVISION NVR32
Brand: SAB Pages: 29
ADTRAN NetVanta Analog Modem Dial Backup Interface Module Quick Start Manual preview
NetVanta Analog Modem Dial Backup Interface Module
Brand: ADTRAN Pages: 2
Bridgeworks Tamar FCSAS102800 User Manual preview
Tamar FCSAS102800
Brand: Bridgeworks Pages: 56
HMS Anybus AWB3000 Startup Manual preview
Anybus AWB3000
Brand: HMS Pages: 18
ADTRAN ENHANCED PSD 239 H2R Product Manual preview
ENHANCED PSD 239 H2R
Brand: ADTRAN Pages: 2
ActiveEye K9504L-W Operation Manual preview
K9504L-W
Brand: ActiveEye Pages: 35
Aerotech QNP3 Series Hardware Manual preview
QNP3 Series
Brand: Aerotech Pages: 62
ZALMAN ZM-GWB3 User Manual preview
ZM-GWB3
Brand: ZALMAN Pages: 9
Multitech FaxFinder FF-120 Administrator User Manual preview
FaxFinder FF-120
Brand: Multitech Pages: 20
Planet FGSW-4840S User Manual preview
FGSW-4840S
Brand: Planet Pages: 38
Korg EXBP-MP3 User Manual preview
EXBP-MP3
Brand: Korg Pages: 8
MSI MPG SEKIRA 500X Manual preview
MPG SEKIRA 500X
Brand: MSI Pages: 2
MSI MPG CORELIQUID K240 User Manual preview
MPG CORELIQUID K240
Brand: MSI Pages: 20
Aaeon PFM-620S Manual preview
PFM-620S
Brand: Aaeon Pages: 45

Brands by name

Popular brands

Load more brands