Renesas SH7706 Series Hardware Manual Download Page 163 | Manualshive

Page: 163 / 749

background image

Section 6 Interrupt Controller (INTC)

Rev. 5.00 May 29, 2006 page 115 of 698

REJ09B0146-0500

6.2

Input/Output Pin

Table 6.1 lists the INTC pin configuration.

Table 6.1

Pin Configuration

Name

Abbreviation

I/O

Description

Nonmaskable interrupt input pin

NMI

I

Nonmaskable interrupt request signal
input

Interrupt input pins

IRQ5 to IRQ0

IRL3

to

IRL0

I

Interrupt request signal input
(Maskable by interrupt mask bits in
SR)

Interrupt request output pin

IRQOUT

O

Output of signal that notifies external
devices that an interrupt source or
memory refresh has occurred

6.3

Interrupt Sources

There are 4 types of interrupt sources: NMI, IRQ, IRL, and on-chip peripheral modules. The
priority of each interrupt is indicated by a priority level value (16 to 0), with level 16 as the
highest and level 1 as the lowest. When level 0 is set, the interrupt is masked and interrupt
requests are ignored.

6.3.1

NMI Interrupts

The NMI interrupt has the highest priority level of 16. When the BLMSK bit of the interrupt
control register (ICR1) is 1 or the BL bit of the status register (SR) is 0, NMI interrupts are
accepted when the MAI bit of the ICR1 register is 0. NMI interrupts are edge-detected. In sleep or
software standby mode, the interrupt is accepted regardless of the BL. The NMI edge select bit
(NMIE) in the interrupt control register 0 (ICR0) is used to select either the rising or falling edge.
When the NMIE bit of the ICR0 register is changed, the NMI interrupt is not detected for 20
cycles after changing the ICR0. NMIE to avoid a false detection of the NMI interrupt. NMI
interrupt exception processing does not affect the interrupt mask level bits (I3 to I0) in the status
register (SR).

When the BL bit is 1 and the BLMSK bit of the ICR1 register is set to 1, only NMI interrupts are
accepted and the SPC register and SSR register are updated by the NMI interrupt handler, making
it impossible to return to the original processing from exception processing initiated prior to the
NMI. Use should therefore be restricted to cases where return is not necessary.

«
...
161
162
163
164
165
...
»

Summary of Contents for SH7706 Series














































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SH7706 Series

Brand: SAF Pages: 30

Protege PRT-PX16-PCB

Brand: ICT Pages: 34

Brand: NA Pages: 22

Brand: National Instruments Pages: 130

UniFi Cloud Key

Brand: Ubiquiti Pages: 13

Brand: Ubiquiti Pages: 21

Brand: Aaeon Pages: 72

EK-FC980 GTX Classy

Brand: ekwb Pages: 2

Brand: Idis Pages: 20

UniFi LED ULED-AT

Brand: Ubiquiti Pages: 16

Brand: IBM Pages: 72

Brand: Keil Pages: 68

Brand: uneron Pages: 13

Brand: Cypress Semiconductor Pages: 38

Brand: ST Pages: 67

FiberTwist XGS2410

Brand: Genexis Pages: 7

Brand: Primera Pages: 82

BreezeNET DS.11 Configuration Utility

Brand: Alvarion Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands