Renesas SH7706 Series Hardware Manual Download | Manualshive

Page: 587 / 749

background image

Section 19 A/D Converter (ADC)

Rev. 5.00 May 29, 2006 page 539 of 698

REJ09B0146-0500

19.6

Operation

The A/D converter operates by successive approximations with 10-bit resolution. It has two
operating modes: single mode and scan mode.

19.6.1

Single Mode (MULTI = 0)

Single mode should be selected when only one A/D conversion on one channel is required. A/D
conversion starts when the ADST bit in ADCSR is set to 1 by software, or by external trigger
input. The ADST bit remains set to 1 during A/D conversion and is automatically cleared to 0
when conversion ends.

When conversion ends the ADF bit is set to 1. If the ADIE bit is also set to 1, an ADI interrupt is
requested at this time. To clear the ADF flag to 0, first read ADCSR, then write 0 in ADF.

When the mode or analog input channel must be switched during A/D conversion, to prevent
incorrect operation, first clear the ADST bit to 0 in ADCSR to halt A/D conversion. After making
the necessary changes, set the ADST bit to 1 to start A/D conversion again. The ADST bit can be
set at the same time as the mode or channel is changed.

Typical operations when channel 1 (AN1) is selected in single mode are described next.

Figure 19.5 shows a timing diagram for this example.

1. Single mode is selected (MULTI = 0), input channel AN1 is selected (CH2 = CH1 = 0, CH0 =

1), the A/D interrupt is enabled (ADIE = 1), and A/D conversion is started (ADST = 1).

2. When A/D conversion is completed, the result is transferred into ADDRB. At the same time

the ADF flag is set to 1, the ADST bit is cleared to 0, and the A/D converter becomes idle.

3. Since ADF = 1 and ADIE = 1, an ADI interrupt is requested.

4. The A/D interrupt processing routine starts.

5. The routine reads ADCSR, then writes 0 in the ADF flag.

6. The routine reads and processes the conversion result (ADDRB = 0).

7. Execution of the A/D interrupt processing routine ends. Then, when the ADST bit is set to 1,

A/D conversion starts to execute 2 to 7 above.

«
...
585
586
587
588
589
...
»

Summary of Contents for SH7706 Series














































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SH7706 Series

Brand: D-Link Pages: 15

Brand: Aastra Pages: 2

Brand: CAME Pages: 19

Brand: Yamaha Pages: 4

Brand: Paradyne Pages: 85

FireWire 800 + Hi-Speed USB Combo

Brand: SIIG Pages: 20

Brand: Comway Pages: 20

Brand: Xenteq Pages: 16

Brand: Maxtor Pages: 2

airMAX NanoBridge M NBM3

Brand: Ubiquiti Pages: 24

SmartRack SR25UBEXP

Brand: Tripp Lite Pages: 4

Brand: PairGain Pages: 80

Acme Packet 3900

Brand: Oracle Pages: 70

airPoint Nexus sB3210

Brand: SmartBridges Pages: 55

Brand: Dinstar Pages: 103

Brand: R.V.R. Elettronica Pages: 171

RJModem MT5656RJ

Brand: Multi-Tech Pages: 27

Brand: Omron Pages: 172

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands