manualshive.com logo in svg

Renesas SH7706 Series, Hardware Manual

The Renesas SH7706 Series is a high-performance microcontroller designed for a wide range of applications. To maximize the potential of this product, it is crucial to have access to its comprehensive "Hardware Manual". This manual can be easily downloaded for free from manualshive.com, providing users with detailed instructions and specifications for optimal usage.

Share
Download
background image

Section 9   Direct Memory Access Controller (DMAC)

Rev. 5.00  May 29, 2006  page 259 of 698

REJ09B0146-0500

Bit

Bit Name

Initial Value

R/W

Description

13

12

SM1

SM0

0

0

R/W

R/W

Source Address Mode

SM1 and SM0 select whether the DMA source
address is incremented, decremented, or left
fixed.

00: Fixed source address

01: Source address is incremented (+1 in 8-bit

transfer, +2 in 16-bit transfer, +4 in 32-bit
transfer, +16 in 16-byte transfer)

10: Source address is decremented (–1 in 8-bit

transfer, –2 in 16-bit transfer, –4 in 32-bit
transfer; illegal setting in 16-byte transfer)

11: Reserved (Setting prohibited)

Notes: If the transfer source is specified in indirect

address, specify the address, in which the
data to be transferred is stored and which
is stored as data (indirect address),
SAR_3.
Specification of SAR_3 increment or
decrement in indirect address mode
depends on SM1 and SM0 settings. In this
case, however, the SAR_3 increment or
decrement value is +4, –4, or fixed to 0
regardless of the transfer data size
specified in TS1 and TS0.

Summary of Contents for SH7706 Series














































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SH7706 Series

Paradyne 3163 Quick Reference preview
3163
Brand: Paradyne Pages: 16
dbx Zone Pro 640 Manual preview
Zone Pro 640
Brand: dbx Pages: 2
dbx 166 Quick Start Manual preview
166
Brand: dbx Pages: 17
ICP DAS USA ZT-2510 Series Quick Start Manual preview
ZT-2510 Series
Brand: ICP DAS USA Pages: 8
Ubiquiti UniFi Cloud Key Quick Start Manual preview
UniFi Cloud Key
Brand: Ubiquiti Pages: 13
Galaxy Hunter Series Quick Start Manual preview
Hunter Series
Brand: Galaxy Pages: 30
Medel RONDO 3 Quick Manual preview
RONDO 3
Brand: Medel Pages: 28
Vega ARIES v3.0 Product Reference Manual preview
ARIES v3.0
Brand: Vega Pages: 12
Omron NJ501-1300 User Manual preview
NJ501-1300
Brand: Omron Pages: 432
ADLINK Technology cPCIS-1100 Series User Manual preview
cPCIS-1100 Series
Brand: ADLINK Technology Pages: 48
Beckhoff EK1122 Documentation preview
EK1122
Brand: Beckhoff Pages: 84
Flexwatch FW3870 User Manual preview
FW3870
Brand: Flexwatch Pages: 13
Jetter JVM-507B - HMI Installation Manual preview
JVM-507B - HMI
Brand: Jetter Pages: 20
ADLINK Technology VPX3000 Series Manual preview
VPX3000 Series
Brand: ADLINK Technology Pages: 95
Idis DR-8516 Installation Manual preview
DR-8516
Brand: Idis Pages: 28
Acces I/O products mPCIe-ADI12-8 Hardware Manual preview
mPCIe-ADI12-8
Brand: Acces I/O products Pages: 13
ST X-NUCLEO-GFX01M Series User Manual preview
X-NUCLEO-GFX01M Series
Brand: ST Pages: 31
Forest CKS Assemblage preview
CKS
Brand: Forest Pages: 5

Brands by name

Popular brands

Load more brands