
access-list (standard)
Enterasys G-Series CLI Reference 20-71
Mode
Any
router
mode.
Example
This
example
shows
how
to
display
IP
access
list
number
101.
This
is
an
extended
access
list,
which
permits
or
denies
ICMP,
UDP
and
IP
frames
based
on
restrictions
configured
with
the
one
of
the
access
‐
list
commands.
For
details
on
configuring
standard
access
lists,
refer
to
“
access
‐
list
(standard)
”
on
page 20
‐
71.
For
details
on
configuring
extended
access
lists,
refer
to
“
access
‐
list
(extended)
”
on
page 20
‐
72
.
G3(su)->router#show access-lists 101
Extended IP access list 101
1: permit icmp host 18.2.32.130 any
2: permit udp host 198.92.32.130 host 171.68.225.126
3: deny ip 150.136.0.0 0.0.255.255 224.0.0.0 15.255.255.255
4: deny ip 11.6.0.0 0.1.255.255 224.0.0.0 15.255.255.255
5: deny ip 172.24.24.0 0.0.1.255 224.0.0.0 15.255.255.255
access-list (standard)
Use
this
command
to
define
a
standard
IP
access
list
by
number
when
operating
in
router
mode.
The
no
form
of
this
command
removes
the
defined
access
list
or
entry.
Syntax
To create an ACL entry:
access-list
access-list-number
{
deny
|
permit
}
source
[
source-wildcard
]
no access-list
access-list-number
[
entry
]
To insert or replace an ACL entry:
access-list
access-list-number
insert | replace
entry
To move entries within an ACL:
access-list
access-list-number
move
destination
source1
[
source2
]
Parameters
access
‐
list
‐
number
Specifies
a
standard
access
list
number.
Valid
values
are
from
1
to
99.
deny
|
permit
Denies
or
permits
access
if
specified
conditions
are
met.
source
Specifies
the
network
or
host
from
which
the
packet
will
be
sent.
Valid
options
for
expressing
source
are:
•
IP
address
or
range
of
addresses
(A.B.C.D)
•
any
‐
Any
source
host
•
host
source
‐
IP
address
of
a
single
source
host
source
‐
wildcard
(Optional)
Specifies
the
bits
to
ignore
in
the
source
address.
insert
|
replace
entry
(Optional)
Inserts
this
new
entry
before
a
specified
entry
in
an
existing
ACL,
or
replaces
a
specified
entry
with
this
new
entry.
Summary of Contents for G3G170-24
