set ciscodp port
Enterasys G-Series CLI Reference 3-11
Defaults
•
Status:
enabled
•
Voice
VLAN:
none
•
Trust
mode:
trusted
•
CoS
value:
0
Mode
Switch
mode,
read
‐
write.
Usage
The
following
points
describe
how
the
Cisco
DP
extended
trust
settings
work
on
the
switch.
•
A
Cisco
DP
port
trust
status
of
trusted
or
untrusted
is
only
meaningful
when
a
Cisco
IP
phone
is
connected
to
a
switch
port
and
a
PC
or
other
device
is
connected
to
the
back
of
the
Cisco
IP
phone.
•
A
Cisco
DP
port
state
of
trusted
or
untrusted
only
affects
tagged
traffic
transmitted
by
the
device
connected
to
the
Cisco
IP
phone.
Untagged
traffic
transmitted
by
the
device
connected
to
the
Cisco
IP
phone
is
unaffected
by
this
setting.
•
If
the
switch
port
is
configured
to
a
Cisco
DP
trust
state
of
trusted
(with
the
trusted
yes
parameter
of
this
command),
this
setting
is
communicated
to
the
Cisco
IP
phone
instructing
it
to
allow
the
device
connected
to
it
to
transmit
traffic
containing
any
CoS
or
Layer
2
802.1p
marking.
•
If
the
switch
port
is
configured
to
a
Cisco
DP
trust
state
of
untrusted
(
trusted
no
),
this
setting
is
communicated
to
the
Cisco
IP
phone
instructing
it
to
overwrite
the
802.1p
tag
of
traffic
transmitted
by
the
device
connected
to
it
to
0,
by
default,
or
to
the
value
specified
by
the
cos
parameter
of
this
command.
•
There
is
a
one
‐
to
‐
one
correlation
between
the
value
set
with
the
cos
parameter
and
the
802.1p
value
assigned
to
ingressed
traffic
by
the
Cisco
IP
phone.
A
value
of
0
equates
to
an
802.1p
priority
of
0.
Therefore,
a
value
of
7
is
given
the
highest
priority.
none
No
voice
VLAN
will
be
used
in
CiscoDP
PDUs.
This
is
the
default.
dot1p
Instructs
attached
phone
to
send
802.1p
tagged
frames.
untagged
Instructs
attached
phone
to
send
untagged
frames.
trusted
Sets
the
extended
trust
mode
on
the
port.
yes
Instructs
attached
phone
to
allow
the
device
connected
to
it
to
transmit
traffic
containing
any
CoS
or
Layer
2
802.1p
marking.
This
is
the
default
value.
no
Instructs
attached
phone
to
overwrite
the
802.1p
tag
of
traffic
transmitted
by
the
device
connected
to
it
to
0,
by
default,
or
to
the
value
configured
with
the
cos
parameter.
cos
value
Instructs
attached
phone
to
overwrite
the
802.1p
tag
of
traffic
transmitted
by
the
device
connected
to
it
with
the
specified
value
,
when
the
trust
mode
of
the
port
is
set
to
untrusted.
Value
can
range
from
0
to
7,
with
0
indicating
the
lowest
priority.
port
‐
string
Specifies
the
port(s)
on
which
status
will
be
set.
Summary of Contents for G3G170-24
