manualshive.com logo in svg

Analog Devices EZ-KIT Lite ADSP-BF506F, Hardware Reference Manual

The Analog Devices EZ-KIT Lite ADSP-BF506F is a high-performance digital signal processing platform. Access the comprehensive System Manual for free download on manualshive.com, offering detailed instructions, enabling users to maximize the potential of their ADSP-BF506F kit. Explore the unbeatable capabilities of this product with our user-friendly manual.

Share
Download
background image

PPI Registers

20-26

ADSP-BF50x Blackfin Processor Hardware Reference

Figure 20-13. PPI Control Register

15 14

13 12

11 10

9

8

7

6

5

4

3

2

1

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

PPI Control Register (PPI_CONTROL)

0 - PPI disabled
1 - PPI enabled

FLD_SEL (Active Field Select)

PORT_DIR (Direction)

XFR_TYPE[1:0] (Transfer
Type)

PORT_CFG[1:0] (Port
Configuration)

PORT_EN (Enable)

DLEN[2:0] (Data Length)

000 - 8 bits
001 - 10 bits
010 - 11 bits
011 - 12 bits
100 - 13 bits
101 - 14 bits
110 - 15 bits
111 - 16 bits

POLS

0 - PPI in Receive mode (input)
1 - PPI in Transmit mode

(output)

In Input mode:
00 - ITU-R 656, Active Field Only
01 - ITU-R 656, Entire Field
10 - ITU-R 656, Vertical Blanking

Only

11 - Non-ITU-R 656 mode
In Output mode:
00, 01, 10 - Sync-less Output

mode

11 - Output mode with 1, 2, or

3 frame syncs

Reset = 0x0000

In ITU-R 656 modes, when XFR_TYPE = 00:
0 - Field 1
1 - Fields 1 and 2
In RX mode with external frame sync, when PORT_CFG = 11:
0 - External trigger
1 - Internal trigger

0 - PPI_FS1 and

PPI_FS2 are treated
as rising edge
asserted

1 - PPI_FS1 and

PPI_FS2 are treated
as falling edge
asserted

SKIP_EN (Skip Enable)

SKIP_EO (Skip Even Odd)

In ITU-R 656 and GP Input modes:
0 - Skip odd-numbered elements
1 - Skip even-numbered elements

In ITU-R 656 and GP Input modes:
0 - Skipping disabled
1 - Skipping enabled

PACK_EN (Packing Mode Enable)

0 - Disabled
1 - Output mode, unpacking enabled;

Input mode, packing enabled

In non-ITU-R 656 Input modes
(PORT_DIR = 0, XFR_TYPE = 11):
00 - 1 external frame sync
01 - 2 or 3 internal frame syncs
10 - 2 or 3 external frame syncs
11 - 0 frame syncs, triggered
In Output modes with frame syncs
(PORT_DIR = 1, XFR_TYPE = 11):
00 - 1 frame sync
01 - 2 or 3 frame syncs
10 - Reserved
11 - Sync PPI_FS3 to assertion of

PPI_FS2 rather than of
PPI_FS1.

POLC

0 - PPI samples data on rising

edge and drives data on
falling edge of PPI_CLK

1 - PPI samples data on falling

edge and drives data on
rising edge of PPI_CLK

Summary of Contents for EZ-KIT Lite ADSP-BF506F































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for EZ-KIT Lite ADSP-BF506F

Analog Devices ADRF5515A-EVALZ User Manual preview
ADRF5515A-EVALZ
Brand: Analog Devices Pages: 9
MSI B450M MORTAR TITANIUM Quick Start Manual preview
B450M MORTAR TITANIUM
Brand: MSI Pages: 144
ASROCK N68-GE Installation Manual preview
N68-GE
Brand: ASROCK Pages: 83
MAX power 125 HYD Series Installation Operation & Maintenance preview
125 HYD Series
Brand: MAX power Pages: 20
Biostar U8788 Reports Manual preview
U8788
Brand: Biostar Pages: 51
Xilinx SP601 User Manual preview
SP601
Brand: Xilinx Pages: 55
ASROCK IMB-1310 Settings Manual preview
IMB-1310
Brand: ASROCK Pages: 2
Microsemi LX7165 User Manual preview
LX7165
Brand: Microsemi Pages: 22
Biostar M7VIT Bravo Test Report preview
M7VIT Bravo
Brand: Biostar Pages: 56
Rohm KX224-I2C-EVK-001 Manual preview
KX224-I2C-EVK-001
Brand: Rohm Pages: 3
ASROCK H97M Pro4 Manual preview
H97M Pro4
Brand: ASROCK Pages: 160
Banana Pi BPI-D1 Manual preview
BPI-D1
Brand: Banana Pi Pages: 25
AOpen MX36LE-UI Installation Manual preview
MX36LE-UI
Brand: AOpen Pages: 8
Biostar G31-M4 Setup Manual preview
G31-M4
Brand: Biostar Pages: 45
Global 3307568 User Manual preview
3307568
Brand: Global Pages: 57
Lucky Star 5V-1B User Manual preview
5V-1B
Brand: Lucky Star Pages: 52
Lucky Star P4VMD+ User Manual preview
P4VMD+
Brand: Lucky Star Pages: 80
Lucky Star 6ABX3 User Manual preview
6ABX3
Brand: Lucky Star Pages: 80

Brands by name

Popular brands

Load more brands