manualshive.com logo in svg

Analog Devices EZ-KIT Lite ADSP-BF506F, Hardware Reference Manual

The Analog Devices EZ-KIT Lite ADSP-BF506F is a high-performance digital signal processing platform. Access the comprehensive System Manual for free download on manualshive.com, offering detailed instructions, enabling users to maximize the potential of their ADSP-BF506F kit. Explore the unbeatable capabilities of this product with our user-friendly manual.

Share
Download
background image

ADSP-BF50x Blackfin Processor Hardware Reference

22-11

ADC Control Module (ACM)

ADC Power Down

The internal ADC available on ADSP-BF506F devices may be transi-
tioned into a power-down mode by asserting and deasserting the

CS

signal

for a number of clock cycles, as described in the “ADC — Modes of Oper-
ation” section of the

ADSP-BF504, ADSP-BF504F, ADSP-BF506F

Embedded Processor Data Sheet

. This ADC power-down mode of the inter-

nal ADC—and external ADCs that support a similar power-down
mechanism—may be achieved by issuing a “dummy” ADC event (or
events) after appropriately programming the T

CSW

field in the

ACM_TC

register.

Single-Shot Sequencing Mode Emulation

In single-shot sequencing mode, all enabled events are sequentially issued
one after the other on the occurrence of an ACM trigger. The sequence of
events is fixed, starting with event 0 and ending with event 15.

Figure 22-5. Single-Shot Sequencing Mode Requirement

SCLK

Trigger

ACMTMR0

CS

ETIME0

ADC

Controls

Event[0]

Event[1]

Event[0]

Summary of Contents for EZ-KIT Lite ADSP-BF506F































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for EZ-KIT Lite ADSP-BF506F

A-Trend 6241 Manual preview
6241
Brand: A-Trend Pages: 40
4gon RouterBOARD 411 Quick Setup Manual And Warranty Information preview
RouterBOARD 411
Brand: 4gon Pages: 2
Abit KG7-RAID User Manual preview
KG7-RAID
Brand: Abit Pages: 104
AOpen MX3W Pro Online Manual preview
MX3W Pro
Brand: AOpen Pages: 156
Elitegroup Computer Systems P6VXM2T Manual preview
P6VXM2T
Brand: Elitegroup Computer Systems Pages: 82
Cypress CYTVII-B-E-1M-SK Quick Start Manual preview
CYTVII-B-E-1M-SK
Brand: Cypress Pages: 19
IEI Technology IMBA-9454G User Manual preview
IMBA-9454G
Brand: IEI Technology Pages: 205
Supermicro H12SSFF-AN6 User Manual preview
H12SSFF-AN6
Brand: Supermicro Pages: 90
Texas Instruments TPS53355EVM-864 User Manual preview
TPS53355EVM-864
Brand: Texas Instruments Pages: 29
Advantech AIMB-287 User Manual preview
AIMB-287
Brand: Advantech Pages: 118
Shuttle Spacewalker AK32 User Manual preview
Spacewalker AK32
Brand: Shuttle Pages: 89
Nuvoton ISD15D00 Troubleshooting Manual preview
ISD15D00
Brand: Nuvoton Pages: 14
ON Semiconductor NB3M8T3910G User Manual preview
NB3M8T3910G
Brand: ON Semiconductor Pages: 19
Gigabyte GA-Q270M-D3H User Manual preview
GA-Q270M-D3H
Brand: Gigabyte Pages: 40
Infineon ISOFACE ISO2H823V2 Manual preview
ISOFACE ISO2H823V2
Brand: Infineon Pages: 28
Arbor Technology EmETXe-i91M0 User Manual preview
EmETXe-i91M0
Brand: Arbor Technology Pages: 68
Javad TRE-G2 Series Application Notes preview
TRE-G2 Series
Brand: Javad Pages: 12
Rohm KXTJ3-1057-EVK-001 User Manual preview
KXTJ3-1057-EVK-001
Brand: Rohm Pages: 3

Brands by name

Popular brands

Load more brands