manualshive.com logo in svg

Analog Devices EZ-KIT Lite ADSP-BF506F, Hardware Reference Manual

The Analog Devices EZ-KIT Lite ADSP-BF506F is a high-performance digital signal processing platform. Access the comprehensive System Manual for free download on manualshive.com, offering detailed instructions, enabling users to maximize the potential of their ADSP-BF506F kit. Explore the unbeatable capabilities of this product with our user-friendly manual.

Share
Download
background image

ADSP-BF50x Blackfin Processor Hardware Reference

24-11

System Reset and Booting

When the

BFLAG_INDIRECT

flag for any block is set, the boot kernel uses

another memory block in L1 data bank A (by default, 0xFF80 7F00–
0xFF80 7FEF) for intermediate data storage. To avoid conflicts, the

elfloader

utility ensures this region is booted last.

The entire source code of the boot ROM is shipped with the CCES or
Vi+ tools installation. Refer to the source code for any addi-
tional questions not covered in this manual. Note that minor maintenance
work may be done to the content of the boot ROM when silicon is
updated.

Block Headers

A boot stream consists of multiple boot blocks, as shown in

Figure 24-3

.

Every block is headed by a 16-byte block header. However, every block
does not necessarily have a payload, as shown in

Figure 24-4

.

Figure 24-3. Booting Process

16-BYTE HEADER FOR BLOCK 1

BLOCK 1

16-BYTE HEADER FOR BLOCK 2

BLOCK 2

16-BYTE HEADER FOR BLOCK 3

BLOCK n

. . .

16-BYTE HEADER FOR BLOCK n

BLOCK 3

FLASH/PROM

APPLICATION

CODE/DATA

ON-CHIP

BOOT ROM

BLOCK 1

BLOCK 3

LI MEMORY

0xEF00 0000

.LDR FILE

B

Summary of Contents for EZ-KIT Lite ADSP-BF506F































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for EZ-KIT Lite ADSP-BF506F

Lantronix xPico 110 User Manual preview
xPico 110
Brand: Lantronix Pages: 17
Avalue Technology EMX-H61 Quick Installation Manual preview
EMX-H61
Brand: Avalue Technology Pages: 12
MIPS Creator CI20 Schematic Diagrams preview
Creator CI20
Brand: MIPS Pages: 10
Acrosser Technology AR-B104D Quick Manual preview
AR-B104D
Brand: Acrosser Technology Pages: 7
SOYO SY-7IWB User Manual preview
SY-7IWB
Brand: SOYO Pages: 95
Intel DH55PJ Product Manual preview
DH55PJ
Brand: Intel Pages: 76
Biostar U8598 Reports Manual preview
U8598
Brand: Biostar Pages: 54
Intel SERVER SYSTEM SR2500AL User Manual preview
SERVER SYSTEM SR2500AL
Brand: Intel Pages: 210
Analog Devices Linear DC2681A-A Demo Manual preview
Linear DC2681A-A
Brand: Analog Devices Pages: 8
ECS A55F-M2 V.2.0 User Manual preview
A55F-M2 V.2.0
Brand: ECS Pages: 74
Supero H8DCT-F User Manual preview
H8DCT-F
Brand: Supero Pages: 78
Global American 3304220 User Manual preview
3304220
Brand: Global American Pages: 37
Gigabyte GA-6WOZ7 User Manual preview
GA-6WOZ7
Brand: Gigabyte Pages: 93
ASROCK Fatal1ty B150 Gaming K4 Manual preview
Fatal1ty B150 Gaming K4
Brand: ASROCK Pages: 154
Texas Instruments TAS6422E-Q1 User Manual preview
TAS6422E-Q1
Brand: Texas Instruments Pages: 35
JETWAY NF18GF User Manual preview
NF18GF
Brand: JETWAY Pages: 45
Biostar U8668 D Bios Setup Manual preview
U8668 D
Brand: Biostar Pages: 32
Systium Technologies Ready 113 User'S Quick Start Manual preview
Ready 113
Brand: Systium Technologies Pages: 4

Brands by name

Popular brands

Load more brands