manualshive.com logo in svg

Analog Devices EZ-KIT Lite ADSP-BF506F, Hardware Reference Manual

The Analog Devices EZ-KIT Lite ADSP-BF506F is a high-performance digital signal processing platform. Access the comprehensive System Manual for free download on manualshive.com, offering detailed instructions, enabling users to maximize the potential of their ADSP-BF506F kit. Explore the unbeatable capabilities of this product with our user-friendly manual.

Share
Download
background image

Functional Description

7-38

ADSP-BF50x Blackfin Processor Hardware Reference

may request a block transfer before the entire buffer is available by simply
taking the minimum transfer time based on wait-state settings into
consideration.

The block count defines how many data transfers are performed by
the MDMA engine. A single DMA transfer can cause two read or
write operations on the EBIU port if the transfer word size is set to
32-bit in the

MDMA_yy_CONFIG

register (

WDSIZE

=

b#10

).

Since the block count registers are 16 bits wide, blocks can group up to
65,535 transfers.

Once a block transfer has been started, the

HMDMAx_BCOUNT

registers return

the remaining number of transfers to complete the current block. When
the complete block has been processed, the

HMDMAx_BCOUNT

register returns

zero. Software can force a reload of the

HMDMAx_BCOUNT

from the

HMDMAx_BCINIT

register even during normal operation by setting the

RBC

bit in the

HMDMAx_CONTROL

register. Set

RBC

when the HMDMA module is

already active, but only when the MDMA is not enabled.

Pipelining DMA Requests

The device mastering the DMA request lines is allowed to request addi-
tional transfers even before the former transfer has completed. As long as
the device can provide or consume sufficient data it is permitted to pulse
the

DMARx

inputs multiple times.

The

HMDMAx_ECOUNT

registers are incremented every time a significant edge

is detected on the respective

DMARx

input, and they are decremented when

the MDMA completes the block transfer. These read-only registers use a
16-bit twos-complement data representation: if they return zero, all
requested block transfers have been performed. A positive value signals up
to 32767 requests that haven’t been served yet and indicates that the
MDMA is currently processing. Negative values indicate the number of
DMA requests that will be ignored by the engine. This feature restrains
initial pulses on the

DMARx

inputs at startup.

Summary of Contents for EZ-KIT Lite ADSP-BF506F































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for EZ-KIT Lite ADSP-BF506F

Biostar TA870 PLUS - SETUP 2 Setup Manual preview
TA870 PLUS - SETUP 2
Brand: Biostar Pages: 67
JETWAY I407R1A User Manual preview
I407R1A
Brand: JETWAY Pages: 52
Renesas ISL8273M User Manual preview
ISL8273M
Brand: Renesas Pages: 17
Pentair FLECK XTR2 Installation & Operation Instructions preview
FLECK XTR2
Brand: Pentair Pages: 4
Embedian SBC-SMART-MEN User Manual preview
SBC-SMART-MEN
Brand: Embedian Pages: 70
DG NVMe-IP Instruction preview
NVMe-IP
Brand: DG Pages: 18
Micronics D5CUB ISA Manual preview
D5CUB ISA
Brand: Micronics Pages: 80
Acorp 4S661QP Manual preview
4S661QP
Brand: Acorp Pages: 74
Watersnake ASP T18-SW Owner'S Manual preview
ASP T18-SW
Brand: Watersnake Pages: 24
MSI MS-7236 Manual preview
MS-7236
Brand: MSI Pages: 78
TYAN S2257 THUNDER 2400 Manual preview
S2257 THUNDER 2400
Brand: TYAN Pages: 105
Texas Instruments DS125BR800EVM User Manual preview
DS125BR800EVM
Brand: Texas Instruments Pages: 14
Asus B85M-K PLUS User Manual preview
B85M-K PLUS
Brand: Asus Pages: 50
Asus C User Manual preview
C
Brand: Asus Pages: 58
Asus CUPLE-VM User Manual preview
CUPLE-VM
Brand: Asus Pages: 92
Asus CUV266-D User Manual preview
CUV266-D
Brand: Asus Pages: 92
Asus B85M-G PLUS Manual preview
B85M-G PLUS
Brand: Asus Pages: 77
Asus CUBX-E User Manual preview
CUBX-E
Brand: Asus Pages: 101

Brands by name

Popular brands

Load more brands