manualshive.com logo in svg

Analog Devices EZ-KIT Lite ADSP-BF506F, Hardware Reference Manual

The Analog Devices EZ-KIT Lite ADSP-BF506F is a high-performance digital signal processing platform. Access the comprehensive System Manual for free download on manualshive.com, offering detailed instructions, enabling users to maximize the potential of their ADSP-BF506F kit. Explore the unbeatable capabilities of this product with our user-friendly manual.

Share
Download
background image

ADSP-BF50x Blackfin Processor Hardware Reference

7-49

Direct Memory Access

ready to perform a transfer, then no transfer is performed, and the stream
selection unlocks and becomes free again on the next cycle.

If round-robin operation is used when only one MDMA stream is active,
one idle cycle will occur for each P MDMA data cycles, slightly lowering
the bandwidth by a factor of 1/(P+1). However if both MDMA streams
are used, memory DMA can operate continuously with zero additional
overhead for alternation of streams. (Other than overhead cycles normally
associated with reversal of read/write direction to memory). By selection
of various round-robin period values P, which limit how often the
MDMA streams alternate, maximal transfer efficiency can be maintained.

Traffic Control

In the Blackfin DMA architecture, there are two completely separate but
simultaneous prioritization processes—the DAB bus prioritization and the
memory bus (DCB and DEB) prioritization. Peripherals that are request-
ing DMA via the DAB bus, and whose data FIFOs are ready to handle the
transfer, compete with each other for DAB bus cycles. Similarly but sepa-
rately, channels whose FIFOs need memory service (prefetch or
post-write) compete together for access to the memory buses. MDMA
streams compete for memory access as a unit, and source and destination
may be granted together if their memory transfers do not conflict. In this
way, internal-to-external or external-to-internal memory transfers may
occur at the full system clock rate (

SCLK

). Examples of memory conflict

include simultaneous access to the same memory space and simultaneous
attempts to fetch descriptors. Special processing may occur if a peripheral
is requesting DMA but its FIFO is not ready (for example, an empty
transmit FIFO or full receive FIFO).

For more information, see “Tempo-

rary DMA Urgency” on page 7-45.

Traffic control is an important consideration in optimizing use of DMA
resources. Traffic control is a way to influence how often the transfer
direction on the data buses may change, by automatically grouping same
direction transfers together. The DMA block provides a traffic control

Summary of Contents for EZ-KIT Lite ADSP-BF506F































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for EZ-KIT Lite ADSP-BF506F

IEI Technology KINO-AH612 Quick Installation Manual preview
KINO-AH612
Brand: IEI Technology Pages: 12
IEI Technology KINO-945GSE User Manual preview
KINO-945GSE
Brand: IEI Technology Pages: 190
IEI Technology KINO-9454 Quick Installation Manual preview
KINO-9454
Brand: IEI Technology Pages: 8
IEI Technology IMBA-H610 User Manual preview
IMBA-H610
Brand: IEI Technology Pages: 193
IEI Technology IMBA-C2360-i2 User Manual preview
IMBA-C2360-i2
Brand: IEI Technology Pages: 182
IEI Technology KINO-DBT Series User Manual preview
KINO-DBT Series
Brand: IEI Technology Pages: 133
Actel FlashPro3 Quick Start Card preview
FlashPro3
Brand: Actel Pages: 2
ASRock Industrial IMB-1712 User Manual preview
IMB-1712
Brand: ASRock Industrial Pages: 44
Intel DH55PJ Product Manual preview
DH55PJ
Brand: Intel Pages: 76
JETWAY S445R1A User Manual preview
S445R1A
Brand: JETWAY Pages: 48
natus otometrics HI-PRO 2 Installation Manual preview
otometrics HI-PRO 2
Brand: natus Pages: 22
Analog Devices AD9361 Reference Manual preview
AD9361
Brand: Analog Devices Pages: 128
Gigabyte GA-B85M-DS3H User Manual preview
GA-B85M-DS3H
Brand: Gigabyte Pages: 36
MSI C807MS-E33 Series Manual preview
C807MS-E33 Series
Brand: MSI Pages: 124
ICP Wafer 5822 User Manual preview
Wafer 5822
Brand: ICP Pages: 50
Lite-on Tech NA280 User Manual preview
NA280
Brand: Lite-on Tech Pages: 49
Gigabyte GA-H170M-HD3 DDR3 User Manual preview
GA-H170M-HD3 DDR3
Brand: Gigabyte Pages: 44
Texas Instruments ADS62PXXEVM User Manual preview
ADS62PXXEVM
Brand: Texas Instruments Pages: 27

Brands by name

Popular brands

Load more brands