manualshive.com logo in svg

Analog Devices EZ-KIT Lite ADSP-BF506F, Hardware Reference Manual

The Analog Devices EZ-KIT Lite ADSP-BF506F is a high-performance digital signal processing platform. Access the comprehensive System Manual for free download on manualshive.com, offering detailed instructions, enabling users to maximize the potential of their ADSP-BF506F kit. Explore the unbeatable capabilities of this product with our user-friendly manual.

Share
Download
background image

ADSP-BF50x Blackfin Processor Hardware Reference

24-77

System Reset and Booting

BFROM_SPIBOOT

Entry address:

0xEF00 000A

Arguments:

• SPI address in

R0

•

dFlags

in

R1

•

dBlockCount

in

R2

•

pCallHook

passed over the stack in [FP+0x14]

• updated block count returned in

R0

C prototype:

s32 bfrom_SpiBoot (

s32 dSpiAddress,

s32 dFlags,

s32 dBlockCount,

ADI_BOOT_HOOK_FUNC* pCallHook);

This SPI master boot routine processes boot streams residing in SPI mem-
ories, using the SPI0 controller. The fourth argument

pCallHook

is passed

over the stack. It provides a hook to call a callback routine after the

ADI_BOOT_DATA

structure is filled with default values. For example, the

pCallHook

routine may overwrite the default value of the

uwSsel

value in

the

ADI_BOOT_DATA

structure. The coding follows the rules of

uwHWAIT

(see

“Boot Host Wait (HWAIT) Feedback Strobe” on page 24-19

). A value of

0x060D represents GPIO

PF13

(

SPI0_SSEL1

).

Additional bits in the

dFlags

word are relevant. The user should always set

the

BFLAG_PERIPHERAL

flag but never the

BFLAG_SLAVE

bit. The

BFLAG_NOAUTO

flag instructs the system to skip the SPI device detection

Summary of Contents for EZ-KIT Lite ADSP-BF506F































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for EZ-KIT Lite ADSP-BF506F

MPS EV6001DN-00D Quick Start Manual preview
EV6001DN-00D
Brand: MPS Pages: 6
NXP Semiconductors USB-KW41Z Quick Start Manual preview
USB-KW41Z
Brand: NXP Semiconductors Pages: 6
Advantech AIMB-562 series Manual preview
AIMB-562 series
Brand: Advantech Pages: 59
Texas Instruments AN-1966 LMH2190 User Manual preview
AN-1966 LMH2190
Brand: Texas Instruments Pages: 11
Analog Devices AD911 Series User Manual preview
AD911 Series
Brand: Analog Devices Pages: 12
MSI MS-7236 Manual preview
MS-7236
Brand: MSI Pages: 78
Carp Design X Series Usual Manual preview
X Series
Brand: Carp Design Pages: 6
SOYO SY-K7VLM-B User Manual preview
SY-K7VLM-B
Brand: SOYO Pages: 91
Analog Devices EVAL-AD5326DBZ User Manual preview
EVAL-AD5326DBZ
Brand: Analog Devices Pages: 14
Texas Instruments TPS3899EVM User Manual preview
TPS3899EVM
Brand: Texas Instruments Pages: 17
SAFEASSURE FRDMGD3160DCMHB Manual preview
FRDMGD3160DCMHB
Brand: SAFEASSURE Pages: 42
Xion AXP600 User Manual preview
AXP600
Brand: Xion Pages: 16
BORETTI EL 145 Manual preview
EL 145
Brand: BORETTI Pages: 6
IBASE Technology MI945P User Manual preview
MI945P
Brand: IBASE Technology Pages: 64
IBASE Technology MI996 User Manual preview
MI996
Brand: IBASE Technology Pages: 83
Newport Vessels Pontoon Series User Manual preview
Pontoon Series
Brand: Newport Vessels Pages: 20
Newport X-32lb Owner'S Manual preview
X-32lb
Brand: Newport Pages: 13
Newport L Series User Manual preview
L Series
Brand: Newport Pages: 19

Brands by name

Popular brands

Load more brands