manualshive.com logo in svg

Analog Devices EZ-KIT Lite ADSP-BF506F, Hardware Reference Manual

The Analog Devices EZ-KIT Lite ADSP-BF506F is a high-performance digital signal processing platform. Access the comprehensive System Manual for free download on manualshive.com, offering detailed instructions, enabling users to maximize the potential of their ADSP-BF506F kit. Explore the unbeatable capabilities of this product with our user-friendly manual.

Share
Download
background image

Programming Model

22-28

ADSP-BF50x Blackfin Processor Hardware Reference

from the two channels. When using the SPORT’s core mode, the
core handler should be registered to handle the data read requests
from the SPORT receiver.

• In addition to SPORT register settings, the PORT registers should

also be set properly to enable the SPORT data pins, ACM clock,
CS, and control and trigger pins.

• Before enabling the ACM (by setting the

ACMEN

bit), all the control

bits of the ACM control register should be programmed properly.
The control bits include the ACM timer’s trigger selects (

TRGSELx

),

trigger input polarities (

TRGPOLx

), CS signal polarity (

CSPOL

), ACM

clock polarity (

CLKPOL

), and serial port unit selection (

EPS

).

• Configure the ACM timing control registers to define the ACM

clock frequency, chip select signal width and setup, and hold and
zero time of ACM control signals.

• Configure the event register pairs (Event Control and Event Time

registers) to create required ACM events.

• The Timer Enabled (

TMRENx

) bits should be programmed together

only after the ACM is enabled, but once the bits are programmed it
should not be changed; modifying the enable bits in the ACM
Control register is not recommended while the ACM is in opera-
tion. Doing so can cause events to change from dependency on one
timer to dependency on the other, and can cause the values in the
ACM status registers (

ACM_STAT

and

ACM_ES

) to be inaccurate.

If an application requires both timers, enable them together after
enabling the ACM. If one timer is already enabled, disable and
re-enable the ACM, and then program both timer enable bits. Sim-
ilarly, when both timers are running, they should disabled
together.

Summary of Contents for EZ-KIT Lite ADSP-BF506F































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for EZ-KIT Lite ADSP-BF506F

hager EG293B User Instructions preview
EG293B
Brand: hager Pages: 4
ASROCK N68C-S Installation Manual preview
N68C-S
Brand: ASROCK Pages: 128
Alcad 912-UC Installation And Programming Manual preview
912-UC
Brand: Alcad Pages: 98
Wintech MV018 User Manual preview
MV018
Brand: Wintech Pages: 5
Avalue Technology EAX-Q35 User Manual preview
EAX-Q35
Brand: Avalue Technology Pages: 89
Intel BOXDP43BF Product Manual preview
BOXDP43BF
Brand: Intel Pages: 78
National Semiconductor LP3972 User Manual preview
LP3972
Brand: National Semiconductor Pages: 13
ON Semiconductor AR0832MBSC25SUFAH-GEVB User Manual preview
AR0832MBSC25SUFAH-GEVB
Brand: ON Semiconductor Pages: 6
JETWAY I407R1A User Manual preview
I407R1A
Brand: JETWAY Pages: 52
Renesas ISL8273M User Manual preview
ISL8273M
Brand: Renesas Pages: 17
Gigabyte GA-9ITDW User Manual preview
GA-9ITDW
Brand: Gigabyte Pages: 76
Unicorn Computer ENDAT-3701 User Manual preview
ENDAT-3701
Brand: Unicorn Computer Pages: 36
Supermicro X11SPG-TF User Manual preview
X11SPG-TF
Brand: Supermicro Pages: 124
ASROCK K8UPGRADE-1689 User Manual preview
K8UPGRADE-1689
Brand: ASROCK Pages: 38
IEI Technology IMBA-9454B-R11 Quick Installation Manual preview
IMBA-9454B-R11
Brand: IEI Technology Pages: 12
DEC Digital Alpha VME 4/224 User Manual preview
Digital Alpha VME 4/224
Brand: DEC Pages: 442
JETWAY 845GLM User Manual preview
845GLM
Brand: JETWAY Pages: 47
Gigabyte 6VTXD User Manual preview
6VTXD
Brand: Gigabyte Pages: 75

Brands by name

Popular brands

Load more brands