manualshive.com logo in svg

Analog Devices EZ-KIT Lite ADSP-BF506F, Hardware Reference Manual

The Analog Devices EZ-KIT Lite ADSP-BF506F is a high-performance digital signal processing platform. Access the comprehensive System Manual for free download on manualshive.com, offering detailed instructions, enabling users to maximize the potential of their ADSP-BF506F kit. Explore the unbeatable capabilities of this product with our user-friendly manual.

Share
Download
background image

ADSP-BF50x Blackfin Processor Hardware Reference

16-19

Two-Wire Interface Controller

Figure 16-9. Clock Stretching During FIFO Underflow

Table 16-5. FIFO Underflow Case

TWI Controller

Processor

Interrupt: XMTSERV – Transmit FIFO buffer
is empty.

Acknowledge: Clear interrupt source bits.
Write transmit FIFO buffer.

...

...

Interrupt: MCOMP – Master transmit com-
plete (DCNT= 0x00).

Acknowledge: Clear interrupt source bits.

S

ADDRESS

DATA

ACK WITH 

STRETCH

ACK

R/W

DATA

ACK

DATA

11

01

00

XMTSTAT[1:0]

TWI_XMT_DATA IS READ AT THIS TIME AND 

CLOCK STRETCHING IS RELEASED.

ACKNOWLEDGE WITH STRETCH

01

SCL

ACKNOWLEDGE "STRETCH" BEGINS SOON AFTER SCL FALL.

Summary of Contents for EZ-KIT Lite ADSP-BF506F































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for EZ-KIT Lite ADSP-BF506F

OEM ITX-945GC3B N330 User Manual preview
ITX-945GC3B N330
Brand: OEM Pages: 38
Embest Altera Lark Board Quick Start Manual preview
Altera Lark Board
Brand: Embest Pages: 9
JETWAY P4XFB User Manual preview
P4XFB
Brand: JETWAY Pages: 48
JETWAY JNP891 Series Quick Start Manual preview
JNP891 Series
Brand: JETWAY Pages: 2
ASROCK Fatal1ty 990FX Professional User Manual preview
Fatal1ty 990FX Professional
Brand: ASROCK Pages: 287
Nuvoton NAU82011WG User Manual preview
NAU82011WG
Brand: Nuvoton Pages: 5
Silicon Laboratories Si5341-EVB User Manual preview
Si5341-EVB
Brand: Silicon Laboratories Pages: 18
DFI 486-OCV Plus User Manual preview
486-OCV Plus
Brand: DFI Pages: 67
JETWAY NF731 User Manual preview
NF731
Brand: JETWAY Pages: 44
Microchip Technology MCP1012 User Manual preview
MCP1012
Brand: Microchip Technology Pages: 44
WynMax Atom D2550 User Manual preview
Atom D2550
Brand: WynMax Pages: 68
Quanmax KEMX-1600 Series User Manual preview
KEMX-1600 Series
Brand: Quanmax Pages: 74
IEI Technology tKINO-AL-E1-R10 Quick Installation Manual preview
tKINO-AL-E1-R10
Brand: IEI Technology Pages: 12
MSI H6M-E22 (G3) User Manual preview
H6M-E22 (G3)
Brand: MSI Pages: 171
Intel BOXDP55KG Product Manual preview
BOXDP55KG
Brand: Intel Pages: 92
Xhorse VVDI Mini Key Tool User Manual preview
VVDI Mini Key Tool
Brand: Xhorse Pages: 17
ITX SECURITY Prodigy M 2022 Compatibility Manual preview
Prodigy M 2022
Brand: ITX SECURITY Pages: 18
Gigabyte GA-M68SM-S2 User Manual preview
GA-M68SM-S2
Brand: Gigabyte Pages: 96

Brands by name

Popular brands

Load more brands