manualshive.com logo in svg

Analog Devices EZ-KIT Lite ADSP-BF506F, Hardware Reference Manual

The Analog Devices EZ-KIT Lite ADSP-BF506F is a high-performance digital signal processing platform. Access the comprehensive System Manual for free download on manualshive.com, offering detailed instructions, enabling users to maximize the potential of their ADSP-BF506F kit. Explore the unbeatable capabilities of this product with our user-friendly manual.

Share
Download
background image

Description of Operation

18-16

ADSP-BF50x Blackfin Processor Hardware Reference

the slave and accepts new data from the master into its shift register, while
it transmits requested data out of the shift register through its SPI trans-
mit data pin. Multiple processors can take turns being the master device,
as can other microcontrollers or microprocessors. One master device can
also simultaneously shift data into multiple slaves (known as broadcast
mode). However, only one slave may drive its output to write data back to
the master at any given time. This must be enforced in broadcast mode,
where several slaves can be selected to receive data from the master, but
only one slave at a time can be enabled to send data back to the master.

In a multimaster or multidevice environment where multiple processors
are connected through their SPI ports, all

MOSI

pins are connected

together, all

MISO

pins are connected together, and all

SCK

pins are con-

nected together.

For a multislave environment, the processor can make use of up to seven
programmable flags that are dedicated SPI slave select signals for the SPI
slave devices.

At reset, the SPI is disabled and configured as a slave.

Clock Signals

The SCK signal is a gated clock that is only active during data transfers for
the duration of the transferred word. The number of active edges is equal
to the number of bits driven on the data lines. The clock rate can be as
high as one-fourth of the SCLK rate. For master devices, the clock rate is
determined by the 16-bit value in the SPI_BAUD register. For slave
devices, the value in SPI_BAUD is ignored. When the SPI device is a mas-
ter, SCK is an output signal. When the SPI is a slave, SCK is an input
signal. Slave devices ignore the serial clock if the slave select input is
driven inactive (high).

The

SCK

signal is used to shift out and shift in the data driven onto the

MISO

and

MOSI

lines. The data is always shifted out on one edge of the

clock and sampled on the opposite edge of the clock. Clock polarity and

Summary of Contents for EZ-KIT Lite ADSP-BF506F































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for EZ-KIT Lite ADSP-BF506F

BCM BC67Q Quick Start Card preview
BC67Q
Brand: BCM Pages: 5
NXP Semiconductors PCA9959HN-ARD Manual preview
PCA9959HN-ARD
Brand: NXP Semiconductors Pages: 32
EPOX EP-3S1A User Manual preview
EP-3S1A
Brand: EPOX Pages: 84
Arbor Technology EmETXe-i91M0 User Manual preview
EmETXe-i91M0
Brand: Arbor Technology Pages: 68
DFI E586-ICP User Manual preview
E586-ICP
Brand: DFI Pages: 96
Honda BF 30 DK2 SHGU Instructions For Use Manual preview
BF 30 DK2 SHGU
Brand: Honda Pages: 132
Octek Panther II Manual preview
Panther II
Brand: Octek Pages: 102
ON Semiconductor CAT872EVB User Manual preview
CAT872EVB
Brand: ON Semiconductor Pages: 3
Mercury 25 Jet FourStroke Operation, Maintenance And Installation Manual preview
25 Jet FourStroke
Brand: Mercury Pages: 110
Alinx AXU2CGA User Manual preview
AXU2CGA
Brand: Alinx Pages: 29
ASROCK Rack EP2C612D16NM Installation Manual preview
EP2C612D16NM
Brand: ASROCK Rack Pages: 2
Texas Instruments ADS1610EVM User Manual preview
ADS1610EVM
Brand: Texas Instruments Pages: 28
Advantech MIC-3389 Manual preview
MIC-3389
Brand: Advantech Pages: 84
ST STM320518-EVAL User Manual preview
STM320518-EVAL
Brand: ST Pages: 52
TYAN S2881 Manual preview
S2881
Brand: TYAN Pages: 64
ASROCK A75 Pro4 MVP Quick Installation Manual preview
A75 Pro4 MVP
Brand: ASROCK Pages: 282
Abit SD7-53 User Manual preview
SD7-53
Brand: Abit Pages: 90
MINN KOTA Ulterra Series User Manual preview
Ulterra Series
Brand: MINN KOTA Pages: 4

Brands by name

Popular brands

Load more brands