manualshive.com logo in svg

Analog Devices EZ-KIT Lite ADSP-BF506F, Hardware Reference Manual

The Analog Devices EZ-KIT Lite ADSP-BF506F is a high-performance digital signal processing platform. Access the comprehensive System Manual for free download on manualshive.com, offering detailed instructions, enabling users to maximize the potential of their ADSP-BF506F kit. Explore the unbeatable capabilities of this product with our user-friendly manual.

Share
Download
background image

ADSP-BF50x Blackfin Processor Hardware Reference

6-23

Internal Flash Memory

When both the program/erase controller status bit and the bank write sta-
tus bit are low (set to ‘0’), the addressed bank is executing a program or
erase operation. When the program/erase controller status bit is low (set to
‘0’) and the bank write status bit is high (set to ‘1’), a program or erase
operation is being executed in a bank other than the one being addressed.

Refer to

“Flowcharts and Pseudo Codes” on page 6-56

for status register

usage.

Table 6-7. Status Register Bits

Bit

Name

Type

Logic

level

1

Definition

SR7

P/EC status

Status

'1'

Ready

'0'

Busy

SR6

Erase suspend
status

Status

'1'

Erase suspended

'0'

Erase in progress or completed

SR5

Erase status

Error

'1'

Erase error

'0'

Erase success

SR4

Program status

Error

'1'

Program error

'0'

Program success

SR3

V

PP

status

Error

'1'

V

PP

invalid, abort

'0'

V

PP

OK

SR2

Program suspend
status

Status

'1'

Program suspended

'0'

Program in progress or completed

SR1

Block protection
status

Error

'1'

Program/erase on protected block, abort

'0'

No operation to protected blocks

Summary of Contents for EZ-KIT Lite ADSP-BF506F































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for EZ-KIT Lite ADSP-BF506F

Gigabyte GA-6KIEH-RH User Manual preview
GA-6KIEH-RH
Brand: Gigabyte Pages: 58
rtd cpuModules CME34BT User Manual preview
cpuModules CME34BT
Brand: rtd Pages: 110
Modular AN003 MPT11210IL User Manual preview
AN003 MPT11210IL
Brand: Modular Pages: 9
Intel D915GAG Product Manual preview
D915GAG
Brand: Intel Pages: 110
Freetech P8F155 User Manual preview
P8F155
Brand: Freetech Pages: 79
Energy EFM32 G890 Manual preview
EFM32 G890
Brand: Energy Pages: 14
ON Semiconductor AR0832MBSC25SUFAH-GEVB User Manual preview
AR0832MBSC25SUFAH-GEVB
Brand: ON Semiconductor Pages: 6
M-system DiskOnChip PCI-G-EVB User Manual preview
DiskOnChip PCI-G-EVB
Brand: M-system Pages: 14
FIC FR33E Manual preview
FR33E
Brand: FIC Pages: 52
Lattice LCMXO3L-DSI-EVN Quick Start preview
LCMXO3L-DSI-EVN
Brand: Lattice Pages: 2
Bartels Mikrotechnik mp6-EVA Operating Manual preview
mp6-EVA
Brand: Bartels Mikrotechnik Pages: 9
TYAN THUNDER I7501 XTREME Manual preview
THUNDER I7501 XTREME
Brand: TYAN Pages: 48
Texas Instruments CC120 Series Quick Start Manual preview
CC120 Series
Brand: Texas Instruments Pages: 7
XFX nForce 680i LT SLI User Manual preview
nForce 680i LT SLI
Brand: XFX Pages: 137
Infineon OPTIREG PMIC TLF30682QVS01 User Manual preview
OPTIREG PMIC TLF30682QVS01
Brand: Infineon Pages: 24
ON Semiconductor CAT4101 User Manual preview
CAT4101
Brand: ON Semiconductor Pages: 2
IEI Technology NANO-945GSE3 User Manual preview
NANO-945GSE3
Brand: IEI Technology Pages: 163
TYAN S2735 Manual preview
S2735
Brand: TYAN Pages: 86

Brands by name

Popular brands

Load more brands