manualshive.com logo in svg

Analog Devices EZ-KIT Lite ADSP-BF506F, Hardware Reference Manual

The Analog Devices EZ-KIT Lite ADSP-BF506F is a high-performance digital signal processing platform. Access the comprehensive System Manual for free download on manualshive.com, offering detailed instructions, enabling users to maximize the potential of their ADSP-BF506F kit. Explore the unbeatable capabilities of this product with our user-friendly manual.

Share
Download
background image

ADSP-BF50x Blackfin Processor Hardware Reference

7-15

Direct Memory Access

Descriptor List Mode

Descriptor list mode is selected by setting the FLOW bit field in the DMA
channel’s DMAx_CONFIG register to either 0x6 (small descriptor mode)
or 0x7 (large descriptor mode). In either of these modes multiple descrip-
tors form a chained list. Every descriptor contains a pointer to the next
descriptor. When the descriptor is fetched, this pointer value is loaded
into the DMAx_NEXT_DESC_PTR register of the DMA channel. In
large descriptor mode this pointer is 32 bits wide. Therefore, the next
descriptor may reside in any address space accessible through the DCB
and DEB buses. In small descriptor mode this pointer is just 16 bits wide.
For this reason, the next descriptor must reside in the same 64K byte
address space as the first one because the upper 16 bits of the
DMAx_NEXT_DESC_PTR register are not updated.

Descriptor list modes are started by writing first to the

DMAx_NEXT_DESC_PTR

register and then to the

DMAx_CONFIG

register.

Descriptor Array Mode

Descriptor array mode is selected by setting the FLOW bit field in the
DMA channel’s DMAx_CONFIG register to 0x4. In this mode, the
descriptors do not contain further descriptor pointers. The initial
DMAx_CURR_DESC_PTR value is written by software. It points to an
array of descriptors. The individual descriptors are assumed to reside next
to each other and, therefore, their addresses are known.

Variable Descriptor Size

In any descriptor-based mode the

NDSIZE

field in the configuration word

specifies how many 16-bit words of the next descriptor need to be loaded
on the next fetch. In descriptor-based operation,

NDSIZE

must be

non-zero. The descriptor size can be any value from one entry (the lower
16 bits of

DMAx_START_ADDR

only) to nine entries (all the DMA parame-

ters).

Table 7-1

illustrates how a descriptor must be structured in

Summary of Contents for EZ-KIT Lite ADSP-BF506F































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for EZ-KIT Lite ADSP-BF506F

Abit VP6 User Manual preview
VP6
Brand: Abit Pages: 112
ASROCK Fatal1ty Z170 Gaming K4 Series Manual preview
Fatal1ty Z170 Gaming K4 Series
Brand: ASROCK Pages: 163
Xilinx ML40 Series Getting Started Tutorial preview
ML40 Series
Brand: Xilinx Pages: 40
DFI 486-OCV Plus User Manual preview
486-OCV Plus
Brand: DFI Pages: 67
Texas Instruments TPS65291 EVM User Manual preview
TPS65291 EVM
Brand: Texas Instruments Pages: 24
AKM AKD4114-B Manual preview
AKD4114-B
Brand: AKM Pages: 30
MediaQ MQ-1168 User Manual preview
MQ-1168
Brand: MediaQ Pages: 25
Variscite VAR-SOM-MX8M-NANO Quick Start Manual preview
VAR-SOM-MX8M-NANO
Brand: Variscite Pages: 2
JETWAY NF731 User Manual preview
NF731
Brand: JETWAY Pages: 44
onsemi NB7NPQ1102MCMUGEVB User Manual preview
NB7NPQ1102MCMUGEVB
Brand: onsemi Pages: 7
Evinrude B4R4 Operator'S Manual preview
B4R4
Brand: Evinrude Pages: 76
Aaeon MB-562 Manual preview
MB-562
Brand: Aaeon Pages: 108
Gigabyte GA-6VM7-4X User Manual preview
GA-6VM7-4X
Brand: Gigabyte Pages: 70
Gigabyte GA-A320M-D2P User Manual preview
GA-A320M-D2P
Brand: Gigabyte Pages: 39
CAME ZBX4 Electrical Connections preview
ZBX4
Brand: CAME Pages: 4
Gigabyte GA-EP45T-DS3 User Manual preview
GA-EP45T-DS3
Brand: Gigabyte Pages: 116
Gigabyte GA-770TA-UD3 User Manual preview
GA-770TA-UD3
Brand: Gigabyte Pages: 120
Lapis ML620Q150A User Manual preview
ML620Q150A
Brand: Lapis Pages: 29

Brands by name

Popular brands

Load more brands