manualshive.com logo in svg

Analog Devices EZ-KIT Lite ADSP-BF506F, Hardware Reference Manual

The Analog Devices EZ-KIT Lite ADSP-BF506F is a high-performance digital signal processing platform. Access the comprehensive System Manual for free download on manualshive.com, offering detailed instructions, enabling users to maximize the potential of their ADSP-BF506F kit. Explore the unbeatable capabilities of this product with our user-friendly manual.

Share
Download
background image

ADSP-BF50x Blackfin Processor Hardware Reference

7-69

Direct Memory Access

The fields of the

DMAx_CONFIG

register are used to set up DMA parameters

and operating modes.

•

FLOW[2:0]

(next operation). This field specifies the type of DMA

transfer to follow the present one. The flow options are:

0x0 - stop. When the current work unit completes, the DMA chan-
nel stops automatically, after signaling an interrupt (if selected).
The

DMA_RUN

status bit in the

DMAx_IRQ_STATUS

register changes

from 1 to 0, while the

DMAEN

bit in the

DMAx_CONFIG

register is

unchanged. In this state, the channel is paused. Peripheral
interrupts are still filtered out by the DMA unit. The channel may
be restarted simply by another write to the

DMAx_CONFIG

register

specifying the next work unit, in which the

DMAEN

bit is set to 1.

0x1 - autobuffer mode. In this mode, no descriptors in memory are
used. Instead, DMA is performed in a continuous circular buffer
fashion based on user-programmed DMA MMR settings. Upon
completion of the work unit, the parameter registers are reloaded
into the current registers, and DMA resumes immediately with
zero overhead. Autobuffer mode is stopped by a user write of 0 to
the

DMAEN

bit in the

DMAx_CONFIG

register.

0x4 - descriptor array mode. This mode fetches a descriptor from
memory that does not include the

NDPH

or

NDPL

elements. Because

the descriptor does not contain a next descriptor pointer entry, the
DMA engine defaults to using the

DMAx_CURR_DESC_PTR

register to

step through descriptors, thus allowing a group of descriptors to
follow one another in memory like an array.

0x6 - descriptor list (small model) mode. This mode fetches a
descriptor from memory that includes

NDPL

, but not

NDPH

. There-

fore, the high 16 bits of the next descriptor pointer field are taken
from the upper 16 bits of the

DMAx_NEXT_DESC_PTR

register, thus

confining all descriptors to a specific 64K page in memory.

Summary of Contents for EZ-KIT Lite ADSP-BF506F































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for EZ-KIT Lite ADSP-BF506F

Gigabyte GA-5BXWL-RH User Manual preview
GA-5BXWL-RH
Brand: Gigabyte Pages: 46
ST STM32746G-EVAL User Manual preview
STM32746G-EVAL
Brand: ST Pages: 79
Linear Technology DC1989A-C Demo Manual preview
DC1989A-C
Brand: Linear Technology Pages: 16
ON Semiconductor AP0100CSSL00SPGAH-GEVB User Manual preview
AP0100CSSL00SPGAH-GEVB
Brand: ON Semiconductor Pages: 6
ST Nucleo STM32F302R8 User Manual preview
Nucleo STM32F302R8
Brand: ST Pages: 18
ASROCK 1U2LW Series User Manual preview
1U2LW Series
Brand: ASROCK Pages: 30
EVGA 122-CK-NF67-A1 User Manual preview
122-CK-NF67-A1
Brand: EVGA Pages: 80
Intel SERVER SYSTEM SR2500AL User Manual preview
SERVER SYSTEM SR2500AL
Brand: Intel Pages: 210
Texas Instruments TPS65257 User Manual preview
TPS65257
Brand: Texas Instruments Pages: 14
EPOX EP-3WXM User Manual preview
EP-3WXM
Brand: EPOX Pages: 68
Gigabyte GA-990FXA-UD7 User Manual preview
GA-990FXA-UD7
Brand: Gigabyte Pages: 112
Texas Instruments AN-1907 LM3423 User Manual preview
AN-1907 LM3423
Brand: Texas Instruments Pages: 17
Gigabyte GA-N650SLI-DS4L User Manual preview
GA-N650SLI-DS4L
Brand: Gigabyte Pages: 100
Micronics M4Pi Series User Manual preview
M4Pi Series
Brand: Micronics Pages: 63
Intel D102GGC2 Quick Reference preview
D102GGC2
Brand: Intel Pages: 1
ON Semiconductor NCP45491PMNGEVB User Manual preview
NCP45491PMNGEVB
Brand: ON Semiconductor Pages: 9
Supero SUPER i2DMR-8G2 User Manual preview
SUPER i2DMR-8G2
Brand: Supero Pages: 78
Gigabyte GA-EP45T-DS3 User Manual preview
GA-EP45T-DS3
Brand: Gigabyte Pages: 116

Brands by name

Popular brands

Load more brands