manualshive.com logo in svg

Analog Devices EZ-KIT Lite ADSP-BF506F, Hardware Reference Manual

The Analog Devices EZ-KIT Lite ADSP-BF506F is a high-performance digital signal processing platform. Access the comprehensive System Manual for free download on manualshive.com, offering detailed instructions, enabling users to maximize the potential of their ADSP-BF506F kit. Explore the unbeatable capabilities of this product with our user-friendly manual.

Share
Download
background image

Dynamic Power Management

1-24

ADSP-BF50x Blackfin Processor Hardware Reference

64×) multiplication factor (bounded by specified minimum and maxi-
mum

VCO

frequencies). The default multiplier is 6×, but it can be modified

by a software instruction sequence. On-the-fly frequency changes can be
made by simply writing to the

PLL_DIV

register.

All on-chip peripherals are clocked by the system clock (

SCLK

). The system

clock frequency is programmable by means of the

SSEL[3:0]

bits of the

PLL_DIV

register.

Dynamic Power Management

The processor provides five operating modes, each with a different perfor-
mance/power profile. In addition, dynamic power management provides
the control functions to dynamically alter the processor core supply volt-
age, further reducing power dissipation. When configured for a 0 volt core
supply voltage, the processor enters the hibernate state. Control of clock-
ing to each of the processor peripherals also reduces power consumption.
See

Table 1-3

for a summary of the power settings for each mode.

Full-On Operating Mode—Maximum Performance

In the full-on mode, the PLL is enabled and is not bypassed, providing
capability for maximum operational frequency. This is the power-up
default execution state in which maximum performance can be achieved.
The processor core and all enabled peripherals run at full speed.

Active Operating Mode—Moderate Dynamic 

Power Savings

In the active mode, the PLL is enabled but bypassed. Because the PLL is
bypassed, the processor’s core clock (CCLK) and system clock (SCLK) run
at the input clock (CLKIN) frequency. DMA access is available to appro-
priately configured L1 memories.

Summary of Contents for EZ-KIT Lite ADSP-BF506F































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for EZ-KIT Lite ADSP-BF506F

Meccanica Fadini Elpro 33 exp Connection Diagram preview
Elpro 33 exp
Brand: Meccanica Fadini Pages: 4
IBM M841LR User Manual preview
M841LR
Brand: IBM Pages: 40
J&W JW-A870T-UC3 User Manual preview
JW-A870T-UC3
Brand: J&W Pages: 40
ST EVAL-L9001 User Manual preview
EVAL-L9001
Brand: ST Pages: 15
Aaeon UPC-Plus User Manual preview
UPC-Plus
Brand: Aaeon Pages: 37
Infineon Technologies Cypress MB39C502-EVBSK-01 Operation Manual preview
Cypress MB39C502-EVBSK-01
Brand: Infineon Technologies Pages: 28
ASROCK N68-GS3 FX Quick Installation Manual preview
N68-GS3 FX
Brand: ASROCK Pages: 154
Gigabyte Z690M DS3H DDR4 User Manual preview
Z690M DS3H DDR4
Brand: Gigabyte Pages: 36
Microchip Technology MCP1012 User Manual preview
MCP1012
Brand: Microchip Technology Pages: 44
WynMax Atom D2550 User Manual preview
Atom D2550
Brand: WynMax Pages: 68
Acorp 4PX400 User Manual preview
4PX400
Brand: Acorp Pages: 74
QDI P5I915PL Manual preview
P5I915PL
Brand: QDI Pages: 47
Gigabyte GA-X99P-SLI User Manual preview
GA-X99P-SLI
Brand: Gigabyte Pages: 88
Yamaha VZ200 2019 Owner'S Manual preview
VZ200 2019
Brand: Yamaha Pages: 80
Yamaha Z300A Supplementary Service Manual preview
Z300A
Brand: Yamaha Pages: 90
Yamaha VZ225B Owner'S Manual preview
VZ225B
Brand: Yamaha Pages: 126
ASROCK P67 PROFESSIONAL Datasheet preview
P67 PROFESSIONAL
Brand: ASROCK Pages: 9
Draper 28218 Instruction Overview preview
28218
Brand: Draper Pages: 49

Brands by name

Popular brands

Load more brands