manualshive.com logo in svg

Analog Devices EZ-KIT Lite ADSP-BF506F, Hardware Reference Manual

The Analog Devices EZ-KIT Lite ADSP-BF506F is a high-performance digital signal processing platform. Access the comprehensive System Manual for free download on manualshive.com, offering detailed instructions, enabling users to maximize the potential of their ADSP-BF506F kit. Explore the unbeatable capabilities of this product with our user-friendly manual.

Share
Download
background image

Description of Operation

4-6

ADSP-BF50x Blackfin Processor Hardware Reference

When an interrupt’s service routine is finished, the RTI instruction
clears the appropriate bit in the

IPEND

register. However, the rele-

vant

SIC_ISR

bit is not cleared unless the service routine clears the

mechanism that generated the interrupt.

Many systems need relatively few interrupt-enabled peripherals, allowing
each peripheral to map to a unique core priority level. In these designs, the

SIC_ISR

register will seldom, if ever, need to be interrogated.

The

SIC_ISR

register is not affected by the state of the

SIC_IMASK

register

and can be read at any time. Writes to the

SIC_ISR

register have no effect

on its contents.

Peripheral DMA channels are mapped in a fixed manner to the peripheral
interrupt IDs. However, the assignment between peripherals and DMA
channels is freely programmable with the

DMA_PERIPHERAL_MAP

registers.

Table 4-1 on page 4-3

and

Table 4-2 on page 4-11

show the default DMA

assignment. Once a peripheral has been assigned to any other DMA chan-
nel it uses the new DMA channel’s interrupt ID regardless of whether
DMA is enabled or not. Therefore, clean

DMA_PERIPHERAL_MAP

manage-

ment is required even if the DMA is not used. The default setup should be
the best choice for all non-DMA applications.

For dynamic power management, any of the peripherals can be configured
to wake up the core from its idled state to process the interrupt, simply by
enabling the appropriate bit in the

SIC_IWR

register (refer to

Table 4-1 on

page 4-3

and

Table 4-2 on page 4-11

). If a peripheral interrupt source is

enabled in

SIC_IWR

and the core is idled, the interrupt causes the DPMC

to initiate the core wakeup sequence in order to process the interrupt.
Note this mode of operation may add latency to interrupt processing,
depending on the power control state. For further discussion of power
modes and the idled state of the core, see the Dynamic Power Manage-
ment chapter.

The

SIC_IWR

register has no effect unless the core is idled. By default, all

interrupts generate a wakeup request to the core. However, for some

Summary of Contents for EZ-KIT Lite ADSP-BF506F































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for EZ-KIT Lite ADSP-BF506F

ASROCK H61M-DG3 Quick Installation Manual preview
H61M-DG3
Brand: ASROCK Pages: 138
IBASE Technology MB991AF User Manual preview
MB991AF
Brand: IBASE Technology Pages: 91
JETWAY NF36-2550 Technical Manual preview
NF36-2550
Brand: JETWAY Pages: 46
MSI MS-9897 User Manual preview
MS-9897
Brand: MSI Pages: 55
Zeal-All ZA-1800MINI User Manual preview
ZA-1800MINI
Brand: Zeal-All Pages: 8
Ebyte E77-400MBL-01 User Manual preview
E77-400MBL-01
Brand: Ebyte Pages: 9
NXP Semiconductors SJA1105SMBEVM User Manual preview
SJA1105SMBEVM
Brand: NXP Semiconductors Pages: 35
NXP Semiconductors LFSTBEB7361 Quick Start Manual preview
LFSTBEB7361
Brand: NXP Semiconductors Pages: 2
ASROCK PHANTOM GAMING B650E PG-ITX WiFi User Manual preview
PHANTOM GAMING B650E PG-ITX WiFi
Brand: ASROCK Pages: 62
Hochiki TCH-B100 Manual preview
TCH-B100
Brand: Hochiki Pages: 8
DFI SB336-Ni User Manual preview
SB336-Ni
Brand: DFI Pages: 105
SOYO SY-K7VMP Quick Start Manual preview
SY-K7VMP
Brand: SOYO Pages: 34
ASROCK A75 Pro4-M Quick Installation Manual preview
A75 Pro4-M
Brand: ASROCK Pages: 260
Abit KD7A User Manual preview
KD7A
Brand: Abit Pages: 80
MSK MSK5031 User Manual preview
MSK5031
Brand: MSK Pages: 10
MSI MEG Z390 GODLIKE Manual preview
MEG Z390 GODLIKE
Brand: MSI Pages: 111
MSI MAG B550M MORTAR WIFI Quick Start Manual preview
MAG B550M MORTAR WIFI
Brand: MSI Pages: 71
MSI MEG Z590 ACE User Manual preview
MEG Z590 ACE
Brand: MSI Pages: 284

Brands by name

Popular brands

Load more brands