manualshive.com logo in svg

Analog Devices EZ-KIT Lite ADSP-BF506F, Hardware Reference Manual

The Analog Devices EZ-KIT Lite ADSP-BF506F is a high-performance digital signal processing platform. Access the comprehensive System Manual for free download on manualshive.com, offering detailed instructions, enabling users to maximize the potential of their ADSP-BF506F kit. Explore the unbeatable capabilities of this product with our user-friendly manual.

Share
Download
background image

ADSP-BF50x Blackfin Processor Hardware Reference

1-15

Introduction

Three distinct ITU-R 656 modes are supported:

• Active video only - The PPI does not read in any data between the

End of Active Video (EAV) and Start of Active Video (SAV) pre-
amble symbols, or any data present during the vertical blanking
intervals. In this mode, the control byte sequences are not stored to
memory; they are filtered by the PPI.

• Vertical blanking only - The PPI only transfers Vertical Blanking

Interval (VBI) data, as well as horizontal blanking information and
control byte sequences on VBI lines.

• Entire field - The entire incoming bit stream is read in through the

PPI. This includes active video, control preamble sequences, and
ancillary data that may be embedded in horizontal and vertical
blanking intervals.

Though not explicitly supported, ITU-R 656 output functionality can be
achieved by setting up the entire frame structure (including active video,
blanking, and control information) in memory and streaming the data out
the PPI in a frame sync-less mode. The processor’s 2-D DMA features
facilitate this transfer by allowing the static frame buffer (blanking and
control codes) to be placed in memory once, and simply updating the
active video information on a per-frame basis.

The general-purpose modes of the PPI are intended to suit a wide variety
of data capture and transmission applications. The modes are divided into
four main categories, each allowing up to 16 bits of data transfer per

PPI_CLK

cycle:

• Data receive with internally generated frame syncs

• Data receive with externally generated frame syncs

• Data transmit with internally generated frame syncs

• Data transmit with externally generated frame syncs

Summary of Contents for EZ-KIT Lite ADSP-BF506F































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for EZ-KIT Lite ADSP-BF506F

Panasonic PAN9520 User Manual preview
PAN9520
Brand: Panasonic Pages: 35
Intel DH61SKCH Product Manual preview
DH61SKCH
Brand: Intel Pages: 48
Intel D510MO Specification Update preview
D510MO
Brand: Intel Pages: 6
AXIOMTEK CAPA313 Quick Installation Manual preview
CAPA313
Brand: AXIOMTEK Pages: 2
Linear Technology DC708 Quick Start Manual preview
DC708
Brand: Linear Technology Pages: 6
ON Semiconductor A5191HRTNGEVB User Manual preview
A5191HRTNGEVB
Brand: ON Semiconductor Pages: 20
Octek RHINO VAP133-ACP User Manual preview
RHINO VAP133-ACP
Brand: Octek Pages: 66
AOpen MK79G-1394 Installation Manual preview
MK79G-1394
Brand: AOpen Pages: 8
Texas Instruments TLV3801EVM User Manual preview
TLV3801EVM
Brand: Texas Instruments Pages: 19
MSI MS-6319 Manual preview
MS-6319
Brand: MSI Pages: 76
MSI K7D Master-L User Manual preview
K7D Master-L
Brand: MSI Pages: 112
MSI K8N Neo3 MS-7135 User Manual preview
K8N Neo3 MS-7135
Brand: MSI Pages: 124
DFI EHL171 Quick Reference preview
EHL171
Brand: DFI Pages: 5
Gigabyte GA-MA74GMT-S2 User Manual preview
GA-MA74GMT-S2
Brand: Gigabyte Pages: 100
QDI P6I440LX/L6 Manual preview
P6I440LX/L6
Brand: QDI Pages: 58
trimond HN440 ATX User Manual preview
HN440 ATX
Brand: trimond Pages: 43
K&B 8950 Owner'S Manual preview
8950
Brand: K&B Pages: 6
Rohm BD9G101G Application Note preview
BD9G101G
Brand: Rohm Pages: 8

Brands by name

Popular brands

Load more brands