manualshive.com logo in svg

Analog Devices EZ-KIT Lite ADSP-BF506F, Hardware Reference Manual

The Analog Devices EZ-KIT Lite ADSP-BF506F is a high-performance digital signal processing platform. Access the comprehensive System Manual for free download on manualshive.com, offering detailed instructions, enabling users to maximize the potential of their ADSP-BF506F kit. Explore the unbeatable capabilities of this product with our user-friendly manual.

Share
Download
background image

ADSP-BF50x Blackfin Processor Hardware Reference

2-1

2 MEMORY

This chapter discusses memory population specific to the ADSP-BF50x
processors. Functional memory architecture is described in

Blackfin Pro-

cessor Programming Reference

.

Memory Architecture

Figure 2-1

provides an overview of the ADSP-BF50x processor system

memory map. For a detailed discussion of how to use them, see

Blackfin

Processor Programming Reference

.

Note the architecture does not define a separate I/O space. All resources
are mapped through the flat 32-bit address space. The memory is
byte-addressable.

The upper portion of internal memory space is allocated to the core and
system MMRs. Accesses to this area are allowed only when the processor is
in supervisor or emulation mode (see the Operating Modes and States
chapter of

Blackfin Processor Programming Reference

).

Summary of Contents for EZ-KIT Lite ADSP-BF506F































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for EZ-KIT Lite ADSP-BF506F

FIC 1stMainboard VG33 Manual preview
1stMainboard VG33
Brand: FIC Pages: 38
Aaeon PCM-LN05 Rev.B Manual preview
PCM-LN05 Rev.B
Brand: Aaeon Pages: 65
Embest SBC9000 User Manual preview
SBC9000
Brand: Embest Pages: 91
Texas Instruments TMP006EVM User Manual preview
TMP006EVM
Brand: Texas Instruments Pages: 23
Biostar TA870 PLUS - SETUP 2 Setup Manual preview
TA870 PLUS - SETUP 2
Brand: Biostar Pages: 67
QDI P4I865 PEA User Manual preview
P4I865 PEA
Brand: QDI Pages: 85
JETWAY NF731V Series User Manual preview
NF731V Series
Brand: JETWAY Pages: 46
A-Trend ATC-6510 Manual preview
ATC-6510
Brand: A-Trend Pages: 60
IWILL Motherboard DJ800 User Manual preview
Motherboard DJ800
Brand: IWILL Pages: 52
Variscite VAR-SOM-MX8M-NANO Quick Start Manual preview
VAR-SOM-MX8M-NANO
Brand: Variscite Pages: 2
TOHATSU MES 4C Owner'S Manual preview
MES 4C
Brand: TOHATSU Pages: 52
Embedian SBC-SMART-MEN User Manual preview
SBC-SMART-MEN
Brand: Embedian Pages: 70
Texas Instruments DEM-DSD1796 User Manual preview
DEM-DSD1796
Brand: Texas Instruments Pages: 24
Mach P4MST-890 Setup Manual preview
P4MST-890
Brand: Mach Pages: 86
MSI X99A WORKSTATION User Manual preview
X99A WORKSTATION
Brand: MSI Pages: 97
Gigabyte MZ32-AR0 Release Notes preview
MZ32-AR0
Brand: Gigabyte Pages: 2
Sony HDV HVBK-1505 Installation Instructions preview
HDV HVBK-1505
Brand: Sony Pages: 2
Technologic Systems TS-7250 TS-72 Series Hardware Manual preview
TS-7250 TS-72 Series
Brand: Technologic Systems Pages: 44

Brands by name

Popular brands

Load more brands