manualshive.com logo in svg

Analog Devices EZ-KIT Lite ADSP-BF506F, Hardware Reference Manual

The Analog Devices EZ-KIT Lite ADSP-BF506F is a high-performance digital signal processing platform. Access the comprehensive System Manual for free download on manualshive.com, offering detailed instructions, enabling users to maximize the potential of their ADSP-BF506F kit. Explore the unbeatable capabilities of this product with our user-friendly manual.

Share
Download
background image

ADSP-BF50x Blackfin Processor Hardware Reference

1-9

Introduction

In addition to the dedicated peripheral DMA channels, there are two
memory DMA channels, which are provided for transfers between the var-
ious memories of the processor system with minimal processor
intervention. Memory DMA transfers can be controlled by a very flexible
descriptor-based methodology or by a standard register-based autobuffer
mechanism.

General-Purpose I/O (GPIO)

Because of the rich set of peripherals, the processor groups the many
peripheral signals to three ports—Port F, Port G, and Port H. Most of the
associated pins are shared by multiple signals. The ports function as multi-
plexer controls.

The processor has 35 bidirectional, general-purpose I/O (GPIO) pins allo-
cated across three separate GPIO modules—PORTFIO, PORTGIO, and
PORTHIO, associated with Port F, Port G, and Port H, respectively.
Each GPIO-capable pin shares functionality with other processor periph-
erals via a multiplexing scheme; however, the GPIO functionality is the
default state of the device upon power-up. Neither GPIO output nor
input drivers are active by default. Each general-purpose port pin can be
individually controlled by manipulation of the port control, status, and
interrupt registers:

• GPIO direction control register – Specifies the direction of each

individual GPIO pin as input or output.

• GPIO control and status registers – The processor employs a “write

one to modify” mechanism that allows any combination of individ-
ual GPIO pins to be modified in a single instruction, without
affecting the level of any other GPIO pins. Four control registers
are provided. One register is written in order to set pin values, one
register is written in order to clear pin values, one register is written

Summary of Contents for EZ-KIT Lite ADSP-BF506F































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for EZ-KIT Lite ADSP-BF506F

Yamaha F8 Owner'S Manual preview
F8
Brand: Yamaha Pages: 82
ST STEVAL-1PS03A User Manual preview
STEVAL-1PS03A
Brand: ST Pages: 13
Bartels Mikrotechnik microComponents mp6-XEVA Operating Manual preview
microComponents mp6-XEVA
Brand: Bartels Mikrotechnik Pages: 9
MSI MS-7758 (v3.x) Manual preview
MS-7758 (v3.x)
Brand: MSI Pages: 92
Lattice CrossLink LIF-MD6000 Master Link Board - Revision C User Manual preview
CrossLink LIF-MD6000 Master Link Board - Revision C
Brand: Lattice Pages: 40
EVGA X79 SLI Visual Manual preview
X79 SLI
Brand: EVGA Pages: 2
Ziatech Corporation ZT 8808A Operating Manual preview
ZT 8808A
Brand: Ziatech Corporation Pages: 412
Linear DC951A Demo Manual preview
DC951A
Brand: Linear Pages: 6
Gigabyte GA-F2A68HM-DS2 User Manual preview
GA-F2A68HM-DS2
Brand: Gigabyte Pages: 36
MSI z170a GAMING M9 ACK User Manual preview
z170a GAMING M9 ACK
Brand: MSI Pages: 109
ASROCK X299 Taichi Manual preview
X299 Taichi
Brand: ASROCK Pages: 200
Gigabyte GA-H270-HD3 User Manual preview
GA-H270-HD3
Brand: Gigabyte Pages: 44
Gigabyte 5SG100 User Manual preview
5SG100
Brand: Gigabyte Pages: 19
JETWAY P4XFCU User Manual preview
P4XFCU
Brand: JETWAY Pages: 48
Watersnake GEO-SPOT GPS SW65/54 Owner'S Manual preview
GEO-SPOT GPS SW65/54
Brand: Watersnake Pages: 44
Mercury KOB 845 NDFSX Manual preview
KOB 845 NDFSX
Brand: Mercury Pages: 42
ECS P6VXM2 Manual preview
P6VXM2
Brand: ECS Pages: 87
MSI A320M gaming pro Manual preview
A320M gaming pro
Brand: MSI Pages: 20

Brands by name

Popular brands

Load more brands