manualshive.com logo in svg

Analog Devices EZ-KIT Lite ADSP-BF506F, Hardware Reference Manual

The Analog Devices EZ-KIT Lite ADSP-BF506F is a high-performance digital signal processing platform. Access the comprehensive System Manual for free download on manualshive.com, offering detailed instructions, enabling users to maximize the potential of their ADSP-BF506F kit. Explore the unbeatable capabilities of this product with our user-friendly manual.

Share
Download
background image

ADSP-BF50x Blackfin Processor Hardware Reference

18-17

SPI-Compatible Port Controller

clock phase relative to data are programmable in the

SPI_CTL

register and

define the transfer format. See

Figure 18-5 on page 18-13

.

Interrupt Output

The SPI has two interrupt output signals: a data interrupt and an error
interrupt.

The behavior of the SPI data interrupt signal depends on the

TIMOD

field

in the

SPI_CTL

register. In DMA mode (

TIMOD

=

b#1X

), the data interrupt

acts as a DMA request and is generated when the DMA FIFO is ready to
be written to (

TIMOD

=

b#11

) or read from (

TIMOD

=

b#10

). In non-DMA

mode (

TIMOD

=

0X

), a data interrupt is generated when the

SPI_TDBR

regis-

ter is ready to be written to (

TIMOD

=

b#01

) or when the

SPI_RDBR

register

is ready to be read from (

TIMOD

=

b#00

).

An SPI error interrupt is generated in a master when a mode fault error
occurs, in both DMA and non-DMA modes. An error interrupt can also
be generated in DMA mode when there is an underflow (

TXE

when

TIMOD

=

b#11

) or an overflow (

RBSY

when

TIMOD

=

b#10

) error condition.

In non-DMA mode, the underflow and overflow conditions set the

TXE

and

RBSY

bits in the

SPI_STAT

register, respectively, but do not generate an

error interrupt.

For more information about this interrupt output, see the discussion of
the

TIMOD

bits in

“SPI Control (SPI_CTL) Register” on page 18-36

.

Functional Description

The following sections describe the functional operation of the SPI.

Summary of Contents for EZ-KIT Lite ADSP-BF506F































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for EZ-KIT Lite ADSP-BF506F

Rabbit BL4S100 Product Manual preview
BL4S100
Brand: Rabbit Pages: 144
Digital Equipment AXPpci 33 Design Manual preview
AXPpci 33
Brand: Digital Equipment Pages: 98
Qiyang QY-IMX6S-V1.2 Hardware Manual preview
QY-IMX6S-V1.2
Brand: Qiyang Pages: 27
Intel DH77EB Specification preview
DH77EB
Brand: Intel Pages: 97
Abit KV-82 User Manual preview
KV-82
Brand: Abit Pages: 48
Aaeon FSB-B75G Manual preview
FSB-B75G
Brand: Aaeon Pages: 95
Gigabyte GA-Z68AP-D3 User Manual preview
GA-Z68AP-D3
Brand: Gigabyte Pages: 112
ASROCK M266A User Manual preview
M266A
Brand: ASROCK Pages: 27
Texas Instruments TPS65291 EVM User Manual preview
TPS65291 EVM
Brand: Texas Instruments Pages: 24
IEI Technology WAFER-CV-N26001 User Manual preview
WAFER-CV-N26001
Brand: IEI Technology Pages: 135
Albatron PX845EV1 Series User Manual preview
PX845EV1 Series
Brand: Albatron Pages: 56
JETWAY NF694L Series User Manual preview
NF694L Series
Brand: JETWAY Pages: 52
JETWAY NP591 Technical Manual preview
NP591
Brand: JETWAY Pages: 44
IEI Technology Nano-PV-D4251 User Manual preview
Nano-PV-D4251
Brand: IEI Technology Pages: 153
JETWAY V266DMU User Manual preview
V266DMU
Brand: JETWAY Pages: 48
Epcom EPC9058 Quick Start Manual preview
EPC9058
Brand: Epcom Pages: 8
DFI CA100-D User Manual preview
CA100-D
Brand: DFI Pages: 115
IWILL DPIILS2 Operation Manual preview
DPIILS2
Brand: IWILL Pages: 54

Brands by name

Popular brands

Load more brands