manualshive.com logo in svg

Analog Devices EZ-KIT Lite ADSP-BF506F, Hardware Reference Manual

The Analog Devices EZ-KIT Lite ADSP-BF506F is a high-performance digital signal processing platform. Access the comprehensive System Manual for free download on manualshive.com, offering detailed instructions, enabling users to maximize the potential of their ADSP-BF506F kit. Explore the unbeatable capabilities of this product with our user-friendly manual.

Share
Download
background image

DMA Registers

7-84

ADSP-BF50x Blackfin Processor Hardware Reference

The

DRQ[1:0]

field is used to control the priority of the MDMA channel

when the HMDMA is disabled, that is, when handshake control is not
being used (see

Table 7-6

).

The

RBC

bit forces the

BCOUNT

register to be reloaded with the

BCINIT

value

while the module is already active. Do not set this bit in the same write
that sets the

HMDMAEN

bit to active.

Table 7-6. DRQ[1:0] Values

DRQ[1:0] Priority

Description

00

Disabled

The MDMA request is disabled.

01

Enabled/S Normal MDMA channel priority. The channel in this mode is limited to

single memory transfers separated by one idle system clock. Request sin-
gle transfer from MDMA channel.

10

Enabled/
M

Normal MDMA channel functionality and priority. Request multiple
transfers from MDMA channel (default).

11

Urgent

The MDMA channel priority is elevated to urgent. In this state, it has
higher priority for memory access than non-urgent channels. If two chan-
nels are both urgent, the lower-numbered channel has priority.

Summary of Contents for EZ-KIT Lite ADSP-BF506F































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for EZ-KIT Lite ADSP-BF506F

Supero X8QB6-F User Manual preview
X8QB6-F
Brand: Supero Pages: 105
ASROCK 775i65GV User Manual preview
775i65GV
Brand: ASROCK Pages: 39
BESTEK BNX-H81 User Manual preview
BNX-H81
Brand: BESTEK Pages: 52
Aaeon FSB-B75G Manual preview
FSB-B75G
Brand: Aaeon Pages: 95
Gigabyte GA-Z68AP-D3 User Manual preview
GA-Z68AP-D3
Brand: Gigabyte Pages: 112
EVGA 122-CK-NF67-A1 User Manual preview
122-CK-NF67-A1
Brand: EVGA Pages: 80
Analog Devices Linear DC2681A-A Demo Manual preview
Linear DC2681A-A
Brand: Analog Devices Pages: 8
ECS A55F-M2 V.2.0 User Manual preview
A55F-M2 V.2.0
Brand: ECS Pages: 74
Supero H8DCT-F User Manual preview
H8DCT-F
Brand: Supero Pages: 78
Analog Devices AD9910 User Manual preview
AD9910
Brand: Analog Devices Pages: 17
MSI 975X Platinum Series User Manual preview
975X Platinum Series
Brand: MSI Pages: 157
AOpen nCK804a-LFS Manual preview
nCK804a-LFS
Brand: AOpen Pages: 44
MINATO MODEL 408e+ Operation Manual preview
MODEL 408e+
Brand: MINATO Pages: 125
Maxim MAX9993 Manual preview
MAX9993
Brand: Maxim Pages: 7
Abit KN9S User Manual preview
KN9S
Brand: Abit Pages: 72
Avalue Technology EAX-Q170P User Manual preview
EAX-Q170P
Brand: Avalue Technology Pages: 79
Gigabyte GA-Z77-HD4 User Manual preview
GA-Z77-HD4
Brand: Gigabyte Pages: 104
MSI MS-7145 Manual preview
MS-7145
Brand: MSI Pages: 106

Brands by name

Popular brands

Load more brands