manualshive.com logo in svg

Analog Devices EZ-KIT Lite ADSP-BF506F, Hardware Reference Manual

The Analog Devices EZ-KIT Lite ADSP-BF506F is a high-performance digital signal processing platform. Access the comprehensive System Manual for free download on manualshive.com, offering detailed instructions, enabling users to maximize the potential of their ADSP-BF506F kit. Explore the unbeatable capabilities of this product with our user-friendly manual.

Share
Download
background image

ADSP-BF50x Blackfin Processor Hardware Reference

22-27

ADC Control Module (ACM)

When the ACM is used in conjunction with the SPORT, the setup
and hold timing requirements for the SPORT data signals with
respect to ACLK are different from those requirements with respect
to internally-generated or externally-supplied SPORT clock. Con-
sult

ADSP-BF504, ADSP-BF504F, ADSP-BF506F Embedded

Processor Data Sheet

for information on these timing requirements.

Programming Model

Because the ACM module is used with the SPORT and PWM controllers,
general-purpose timer, and general-purpose ports, programs must comply
with the following to ensure its reliable operation:

• The ACM is a control module that provides clock and chip select

and control signals with required timing to the ADC device. For
capturing the data from the ADC, use either

SPORT0

or

SPORT1

on

the receiver side of the processor.

• The ACM should be enabled before the SPORT controller is

enabled, however, the SPORT can be configured before the ACM
is enabled. The SPORT receiver should be configured in slave
mode (external clock (

IRCLK=0

) and external frame sync (

IRFS=0

)).

• External ADC timing determines the settings of the SPORT con-

troller register’s

LRFS

,

LARFS

,

RCKFE

, and

RLSBIT

bits.

• The SPORT receiver’s DMA mode is preferred because it saves the

processor MIPS when receiving chunks of data. However, receiving
ADC samples in core mode is also possible. When using DMA
mode, the DMA registers of the selected SPORT channel should
be configured appropriately; DMA must be enabled before
enabling the SPORT. When using both the primary and secondary
SPORT channels to receive data from two ADC channels, the 2D
feature of DMA can be effectively used to de-interleave the data

Summary of Contents for EZ-KIT Lite ADSP-BF506F































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for EZ-KIT Lite ADSP-BF506F

Actel FlashPro3 Quick Start Card preview
FlashPro3
Brand: Actel Pages: 2
Quanmax KEEX-1850 Series User Manual preview
KEEX-1850 Series
Brand: Quanmax Pages: 61
ECS UM4980 User Manual preview
UM4980
Brand: ECS Pages: 46
DFI G586IPC User Manual preview
G586IPC
Brand: DFI Pages: 60
ECS NFORCE6M-A User Manual preview
NFORCE6M-A
Brand: ECS Pages: 70
IWILL P4SE2 User Manual preview
P4SE2
Brand: IWILL Pages: 48
JETWAY NF18GF User Manual preview
NF18GF
Brand: JETWAY Pages: 45
MiTAC E8020 User Manual preview
E8020
Brand: MiTAC Pages: 132
Ublox EVK-NORA-W36 User Manual preview
EVK-NORA-W36
Brand: Ublox Pages: 18
DFI SD170 User Manual preview
SD170
Brand: DFI Pages: 48
MSI X99A SLI PLUS User Manual preview
X99A SLI PLUS
Brand: MSI Pages: 108
SOLTEK SL-75DRV2 User Manual preview
SL-75DRV2
Brand: SOLTEK Pages: 100
American GA-8IEX Series User Manual preview
GA-8IEX Series
Brand: American Pages: 41
Texas Instruments LMP91051EVM User Manual preview
LMP91051EVM
Brand: Texas Instruments Pages: 20
Intel DB43LD Product Manual preview
DB43LD
Brand: Intel Pages: 80
JETWAY TIH77MG7 User Manual preview
TIH77MG7
Brand: JETWAY Pages: 18
JETWAY S755MAX User Manual preview
S755MAX
Brand: JETWAY Pages: 46
JETWAY S450 User Manual preview
S450
Brand: JETWAY Pages: 48

Brands by name

Popular brands

Load more brands