manualshive.com logo in svg

Analog Devices EZ-KIT Lite ADSP-BF506F, Hardware Reference Manual, Page: 910 / 1310

Share
Download
Analog Devices EZ-KIT Lite ADSP-BF506F Hardware Reference Manual Download Page 910

SPORT Registers

19-52

ADSP-BF50x Blackfin Processor Hardware Reference

•

Late transmit frame sync

. (

LATFS

). This bit configures late frame

syncs (if set) or early frame syncs (if cleared).

•

Clock drive/sample edge select

. (

TCKFE

). This bit selects which

edge of the

TCLKx

signal the SPORT uses for driving data, for driv-

ing internally generated frame syncs, and for sampling externally
generated frame syncs. If set, data and internally generated frame
syncs are driven on the falling edge, and externally generated frame
syncs are sampled on the rising edge. If cleared, data and internally
generated frame syncs are driven on the rising edge, and externally
generated frame syncs are sampled on the falling edge.

•

TxSec enable

. (

TXSE

). This bit enables the transmit secondary side

of the SPORT (if set).

•

Stereo serial enable

. (

TSFSE

). This bit enables the stereo serial oper-

ating mode of the SPORT (if set). By default this bit is cleared,
enabling normal clocking and frame sync.

•

Left/Right order

. (

TRFST

). If this bit is set, the right channel is

transmitted first in stereo serial operating mode. By default this bit
is cleared, and the left channel is transmitted first.

SPORT Receive Configuration  

(SPORT_RCR1 and SPORT_RCR2) Registers

The main control registers for the receive portion of each SPORT are the
receive configuration registers, SPORT_RCR1 and SPORT_RCR2,
shown in

Figure 19-27

and

Figure 19-28

.

A SPORT is enabled for receive if bit 0 (

RSPEN

) of the receive configura-

tion 1 register is set to 1. This bit is cleared during either a hard reset or a
soft reset, disabling all SPORT reception.

Summary of Contents for EZ-KIT Lite ADSP-BF506F































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments