manualshive.com logo in svg

Analog Devices EZ-KIT Lite ADSP-BF506F, Hardware Reference Manual

The Analog Devices EZ-KIT Lite ADSP-BF506F is a high-performance digital signal processing platform. Access the comprehensive System Manual for free download on manualshive.com, offering detailed instructions, enabling users to maximize the potential of their ADSP-BF506F kit. Explore the unbeatable capabilities of this product with our user-friendly manual.

Share
Download
background image

Command Interface to Internal Flash Memory

6-24

ADSP-BF50x Blackfin Processor Hardware Reference

Configuration Register 

The configuration register configures the type of bus access that the inter-
nal flash memory performs. Refer to

“Read Modes” on page 6-33

for

details on read operations.

The configuration register is set through the command interface. After a
reset or power-up the device is configured for asynchronous page read
(

CR15 = 1

). The configuration register bits are described in

Table 6-9 on

page 6-28

. They specify the selection of the burst length, burst type, burst

X latency, and the read operation.

Since the internal flash device in ADSP-BF50xF processors can only be
connected to the external bus interface unit (EBIU), some combinations
of the flash configurations are not supported. Limitation on supported
combinations are described in the section

“Supported Configuration Reg-

ister Combinations in ADSP-BF50xF Processors” on page 6-84

.

Read Select Bit (CR15) 

The read select bit,

CR15

, switches between asynchronous and synchronous

bus read operations. When the read select bit is set to ‘1’, read operations

SR0

Bank write status

Status

'1'

SR7 = ‘1’

Not allowed

SR7 = ‘0’

Program or erase operation in a bank
other than the addressed bank

'0'

SR7 = ‘1’

No program or erase operation in the
device

SR7 = ‘0’

Program or erase operation in
addressed bank

1

Logic level '1' is High, '0' is Low.

Table 6-7. Status Register Bits (Cont’d)

Bit

Name

Type

Logic

level

1

Definition

Summary of Contents for EZ-KIT Lite ADSP-BF506F































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for EZ-KIT Lite ADSP-BF506F

Gigabyte GS-R12PE Service Manual preview
GS-R12PE
Brand: Gigabyte Pages: 74
Linear Technology DC2581A Demo Manual preview
DC2581A
Brand: Linear Technology Pages: 10
Diamond Systems Athena II User Manual preview
Athena II
Brand: Diamond Systems Pages: 112
Atmel AT91EB42 User Manual preview
AT91EB42
Brand: Atmel Pages: 30
ASROCK Rack C246 WSI User Manual preview
C246 WSI
Brand: ASROCK Rack Pages: 83
ECS A68F2P-M2 User Manual preview
A68F2P-M2
Brand: ECS Pages: 61
Gigabyte GA-C1037UN-LA User Manual preview
GA-C1037UN-LA
Brand: Gigabyte Pages: 32
CHAINTECH 7AIA6 Manual preview
7AIA6
Brand: CHAINTECH Pages: 49
Gigabyte GA-M68SM-S2 User Manual preview
GA-M68SM-S2
Brand: Gigabyte Pages: 96
Mercury 25 Jet FourStroke Operation, Maintenance And Installation Manual preview
25 Jet FourStroke
Brand: Mercury Pages: 110
trimond IN440 Micro-ATX User Manual preview
IN440 Micro-ATX
Brand: trimond Pages: 47
ASROCK CONROE865GV Installation Manual preview
CONROE865GV
Brand: ASROCK Pages: 106
Supermicro X11SSV-M4F User Manual preview
X11SSV-M4F
Brand: Supermicro Pages: 107
ST STEVAL-IHM022V1 User Manual preview
STEVAL-IHM022V1
Brand: ST Pages: 58
DFI SB102-D User Manual preview
SB102-D
Brand: DFI Pages: 59
DFI P4X533-ALE User Manual preview
P4X533-ALE
Brand: DFI Pages: 113
Supero X8ST3-F User Manual preview
X8ST3-F
Brand: Supero Pages: 105
Asus P2L97-S User Manual preview
P2L97-S
Brand: Asus Pages: 68

Brands by name

Popular brands

Load more brands