manualshive.com logo in svg

Analog Devices EZ-KIT Lite ADSP-BF506F, Hardware Reference Manual

The Analog Devices EZ-KIT Lite ADSP-BF506F is a high-performance digital signal processing platform. Access the comprehensive System Manual for free download on manualshive.com, offering detailed instructions, enabling users to maximize the potential of their ADSP-BF506F kit. Explore the unbeatable capabilities of this product with our user-friendly manual.

Share
Download
background image

Specific Boot Modes

24-44

ADSP-BF50x Blackfin Processor Hardware Reference

Specific Boot Modes

This section discusses individual boot modes and the required hardware
connections.

The boot modes differ in terms of the booting source— for example
whether data is loaded through the SPI or the parallel interface. Boot
modes can also be grouped into slave boot modes and master boot modes.

In slave boot modes, the Blackfin processor functions as a slave to any host
device, which is typically another embedded processor, an FPGA device or
even a desktop computer. Likely, the Blackfin processor

RESET

input is

controlled by the host device. So, usually the host sets

RESET

first, then

waits until the preboot routine terminates by sensing the

HWAIT

output,

and finally provides the boot data.

If a Blackfin processor, configured to operate in any of the slave boot
modes, awakens from hibernate, it cannot boot by its own control. A feed-
back mechanism has to be implemented at the system level to inform the
host device whether the processor is in hibernate state or not. The

HWAIT

strobe is an important primitive in such systems.

In the master boot modes, the Blackfin processor usually does not need to
be synchronized and can load the boot data by itself. Master modes typi-
cally read from memory. This can be parallel memory such as flash
devices, or serial memory that is read through SPI interfaces.

Memory boot modes should also be differentiated from peripheral boot
modes. Boot modes that load boot streams through memory DMA are
referred to as memory boot mode, reading data from regular memory.
Peripheral modes load boot data through peripherals such as UART. All
memory boot modes are master modes. The boot source is typically
non-volatile memory, such as a flash or EPROM device or even on-chip
ROM. When supported by the system in warm boot scenarios, the boot
source can also be SRAM.

Summary of Contents for EZ-KIT Lite ADSP-BF506F































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for EZ-KIT Lite ADSP-BF506F

Balluff BIS Series Manual preview
BIS Series
Brand: Balluff Pages: 62
ON Semiconductor A5191HRTNGEVB User Manual preview
A5191HRTNGEVB
Brand: ON Semiconductor Pages: 20
Gigabyte GA-P61-USB3P User Manual preview
GA-P61-USB3P
Brand: Gigabyte Pages: 100
NXP Semiconductors QN908x User Manual preview
QN908x
Brand: NXP Semiconductors Pages: 28
NXP Semiconductors LPCXpresso804 User Manual preview
LPCXpresso804
Brand: NXP Semiconductors Pages: 16
JETWAY J-791A User Manual preview
J-791A
Brand: JETWAY Pages: 37
Freetech P8F217 Series User Manual preview
P8F217 Series
Brand: Freetech Pages: 48
MSI 790XT-G35 series Manual preview
790XT-G35 series
Brand: MSI Pages: 103
Gigabyte MX33-BS0 User Manual preview
MX33-BS0
Brand: Gigabyte Pages: 81
Texas Instruments bq76PL536PGM-1 Quick Start Manual preview
bq76PL536PGM-1
Brand: Texas Instruments Pages: 15
Parker ACR8010 Hardware Manual preview
ACR8010
Brand: Parker Pages: 56
Biostar TF570 Setup Manual preview
TF570
Brand: Biostar Pages: 115
Arbor Technology EmETXe-i91M0 User Manual preview
EmETXe-i91M0
Brand: Arbor Technology Pages: 68
ON Semiconductor NCS2632 User Manual preview
NCS2632
Brand: ON Semiconductor Pages: 7
Supermicro A2SDi-16C-TP8F User Manual preview
A2SDi-16C-TP8F
Brand: Supermicro Pages: 109
Texas Instruments TMP1075EVM User Manual preview
TMP1075EVM
Brand: Texas Instruments Pages: 33
ASROCK H97M Anniversary User Manual preview
H97M Anniversary
Brand: ASROCK Pages: 152
Microchip Technology MCP2221 User Manual preview
MCP2221
Brand: Microchip Technology Pages: 54

Brands by name

Popular brands

Load more brands