manualshive.com logo in svg

Analog Devices EZ-KIT Lite ADSP-BF506F, Hardware Reference Manual

The Analog Devices EZ-KIT Lite ADSP-BF506F is a high-performance digital signal processing platform. Access the comprehensive System Manual for free download on manualshive.com, offering detailed instructions, enabling users to maximize the potential of their ADSP-BF506F kit. Explore the unbeatable capabilities of this product with our user-friendly manual.

Share
Download
background image

Functional Description

14-30

ADSP-BF50x Blackfin Processor Hardware Reference

and the chopping frequency is therefore an integral subdivision of the
system clock frequency:

The

GDCLK

value may range from 0 to 255, which corresponds to a pro-

grammable chopping frequency rate from 97.7 kHz to 25 MHz for a
100 MHz f

SCLK

rate. The gate drive features must be programmed before

operation of the PWM Controller and typically are not changed during
normal operation of the PWM Controller. Following a reset, all bits of the

PWM_GATE

register are cleared so that high-frequency chopping is disabled,

by default.

PWM Polarity Control

The polarity of the PWM signals produced at output pins

AH

to

CL

can be

programmed via the

PWM_POLARITY

bit of the

PWM_CTRL

register. Setting

Figure 14-8. Example of Active Low PWM Signals for Gate Chopping

f

chop

f

SCLK

4

GDCLK

1

+

--------------------------------------------------

=

PWMCHA

PWMCHA

2*PWMDT

PWM_AH

PWM_AL

+PWMTM/2

+PWMTM/2

-PWMTM/2

COUNT

0

0

2*PWMDT

Summary of Contents for EZ-KIT Lite ADSP-BF506F































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for EZ-KIT Lite ADSP-BF506F

Qiyang QY-IMX6S-V1.2 Hardware Manual preview
QY-IMX6S-V1.2
Brand: Qiyang Pages: 27
IEI Technology NANO-945GSE2 Quick Installation Manual preview
NANO-945GSE2
Brand: IEI Technology Pages: 15
JETWAY MU03 Series User Manual preview
MU03 Series
Brand: JETWAY Pages: 49
Modular AN003 MPT11210IL User Manual preview
AN003 MPT11210IL
Brand: Modular Pages: 9
XFX GeForce 8300 (MI-A78U-8309) User Manual preview
GeForce 8300 (MI-A78U-8309)
Brand: XFX Pages: 26
IEI Technology KINO-QM57A User Manual preview
KINO-QM57A
Brand: IEI Technology Pages: 160
Fujitsu Siemens Computers D1421 Technical Manual preview
D1421
Brand: Fujitsu Siemens Computers Pages: 20
Photonic Universe LUX-PRG User Manual preview
LUX-PRG
Brand: Photonic Universe Pages: 6
Gigabyte GA-7DPXDW User Manual preview
GA-7DPXDW
Brand: Gigabyte Pages: 60
Pegatron IPMTB-GS Reference Manual preview
IPMTB-GS
Brand: Pegatron Pages: 30
Gigabyte X570S AORUS PRO AX User Manual preview
X570S AORUS PRO AX
Brand: Gigabyte Pages: 52
OLIMEX AM3352-SOM User Manual preview
AM3352-SOM
Brand: OLIMEX Pages: 26
Biostar P4 TSE Pro User Manual preview
P4 TSE Pro
Brand: Biostar Pages: 40
AOpen AX59PRO User Manual preview
AX59PRO
Brand: AOpen Pages: 11
IEI Technology IMBA-G412ISA User Manual preview
IMBA-G412ISA
Brand: IEI Technology Pages: 164
Texas Instruments TPS2378 User Manual preview
TPS2378
Brand: Texas Instruments Pages: 20
Supero Supero X9DRW-7TPF User Manual preview
Supero X9DRW-7TPF
Brand: Supero Pages: 119
Yamaha VZ225C Owner'S Manual preview
VZ225C
Brand: Yamaha Pages: 124

Brands by name

Popular brands

Load more brands