manualshive.com logo in svg

Analog Devices EZ-KIT Lite ADSP-BF506F, Hardware Reference Manual

The Analog Devices EZ-KIT Lite ADSP-BF506F is a high-performance digital signal processing platform. Access the comprehensive System Manual for free download on manualshive.com, offering detailed instructions, enabling users to maximize the potential of their ADSP-BF506F kit. Explore the unbeatable capabilities of this product with our user-friendly manual.

Share
Download
background image

Interface Overview

22-8

ADSP-BF50x Blackfin Processor Hardware Reference

For all trigger signals, The active edge of the triggers is programmable in
the ACM_CTL register as either rising edge or falling edge.

Figure 22-4

shows the detailed ACM trigger generation logic.

When trigger sources external to the processor are used for triggering the
ACM, (for example, external signals at the GPIO, timer, or PWM sync
pins), the minimum pulse width for such trigger sources needs to be
1 SCLK  1 ns.

Figure 22-4. ACM Trigger Logic

ACM

PWM0, PWM1

TMR

GPIO

Is PG5 or PF10 configured 

in output GPIO mode?

Is PG5 or PF10 configured 

in input GPIO mode?

Is PG5 or PF10 configured 

in timer function mode?

Is PWM1 configured 

for internal sync generation?

Is PWM0 configured 

for internal sync generation?

0, 0

PG5 and PF10 pin inputs

Externally-supplied 

sync signals 

to PWM0 and PWM1

ACM trigger inputs 0,1,2,3

ACM

trigger

inputs

0,1

ACM

trigger

inputs

2,3

TMR7, TMR2

GPIO on PG5, GPIO on PF10

Internally

generated

sync signal
from PWM0

or PWM1

Summary of Contents for EZ-KIT Lite ADSP-BF506F































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for EZ-KIT Lite ADSP-BF506F

Acer V65XA Safety Instructions preview
V65XA
Brand: Acer Pages: 15
Acer V60N Safety Instructions preview
V60N
Brand: Acer Pages: 12
NXP Semiconductors SJA1124EVB Quick Start Manual preview
SJA1124EVB
Brand: NXP Semiconductors Pages: 12
ASROCK 1U2LW Series User Manual preview
1U2LW Series
Brand: ASROCK Pages: 30
Abit KV-82 User Manual preview
KV-82
Brand: Abit Pages: 48
Xilinx Avnet Ultra96-PYNQ Manual preview
Avnet Ultra96-PYNQ
Brand: Xilinx Pages: 19
Xtralis VESDA LCD Programmer Module Product Manual preview
LCD Programmer Module
Brand: Xtralis VESDA Pages: 54
ECS P67H2-A4 Manual preview
P67H2-A4
Brand: ECS Pages: 92
Supermicro X11SPG-TF User Manual preview
X11SPG-TF
Brand: Supermicro Pages: 124
MSI MS-7602 Manual preview
MS-7602
Brand: MSI Pages: 92
ST STEVAL-IHM011V1 User Manual preview
STEVAL-IHM011V1
Brand: ST Pages: 27
Hitachi H8/Tiny 3664F User Manual preview
H8/Tiny 3664F
Brand: Hitachi Pages: 56
Hitachi Compute Blade 2000 Installation Manual preview
Compute Blade 2000
Brand: Hitachi Pages: 52
Hitachi SH7760 Solution Engine2 Overview preview
SH7760 Solution Engine2
Brand: Hitachi Pages: 138
Hitachi Compute Blade 2500 Getting Started Manual preview
Compute Blade 2500
Brand: Hitachi Pages: 154
MATSONIC MS7102C Manual preview
MS7102C
Brand: MATSONIC Pages: 52
Asus Z97-P Manual preview
Z97-P
Brand: Asus Pages: 86
Asus Z97-K R2.0 User Manual preview
Z97-K R2.0
Brand: Asus Pages: 88

Brands by name

Popular brands

Load more brands